Bedienungsanleitung Graupner MICRO MAGIC 2014 (Seite 6 von 15) (Englisch)

637252

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

#0057088

Keine Haftung für Druckfehler. Technische Änderungen vorbehalten! No liability for printing errors. We reserve the right to introduce

modifications. Sous réserve de modifications! Nous ne sommes pas responsables d’éventuelles erreurs d’impression! 11/2006

at the marked points, then form the slot by running

a sharp knife between the two holes, working as

accurately as you can. The slot should only be

trimmed to final size when the deck and hull have

finally been joined.

• The deck can now be glued to the hull: the first step

is to check that the two parts are a snug fit

together; if not, trim them carefully until they are an

accurate fit. Apply UHU plus (e.g. Order No. 962) to

the bow reinforcement (part 9) and the central

girder (part 25) where the parts meet. Now apply

plenty of UHU plast spezial to the edge of the deck

- omitting the stern area - and join the parts without

delay. IMPORTANT: ensure that neither the hull

nor the deck is distorted when the parts are joined.

Hold the hull and deck together using adhesive

tape or rubber bands while the glue is hardening.

However, don’t apply too much pressure, or the hull

will distort. Allow the glue to cure completely, then

apply a little UHU plast spezial along the joint

edges to fill any lurking gaps.

• Apply plenty of high-viscosity (thick) cyano-acrylate

glue to the unglued gap at the stern. TIP: move the

parts relative to each other to persuade the

adhesive to work its way into the joint. Tape the

stern area together while the cyano is hardening.

• The stern area can now be sanded flat;

alternatively you can leave the hull projecting

slightly beyond the deck.

• At this point you must check the hull / deck joint for

leaks. You may need to run more cyano along the

joint to fill any remaining gaps.

• The deck can now be stiffened by gluing the central

bulkhead (part 19) to the keel / mast socket (part

5).

• The rudder bush (part 26) is glued in the hull next;

you may need to trim the hole slightly. Position the

rudder bush in the hull as shown on the plan, and

glue it in place using think cyano, forming a narrow

fillet of adhesive round the bush at top and bottom.

Allow the glue to cure completely, then sand back

the underside flush with the hull. It is important that

the gap between the rudder (part 27) and the

surface of the hull is as small as possible. If the gap

is not even, you may need to trim the top edge of

the rudder blade to match the shape of the hull.

• Set the rudder servo (part 28) to centre from the

transmitter, fit the output arm (part 29) on it, and

install the servo in the servo plate using the

retaining screws provided.

• Assemble the tiller (part 30) from the plastic lever,

the collet and the M3 screw. Fit the tiller assembly

on the rudder shaft and tighten the retaining screw.

• Drill two 2 mm Ø holes for the cable guides (part

31) in the positions shown, cut two 15 mm lengths

from the snake inner sleeve provided, and glue

them in the holes in the hull using cyano.

IMPORTANT: ensure that the guides are angled

correctly, so that the cables have as straight a run

as possible when installed at a later stage.

• Drill two 4 mm Ø holes in the hull for the sheet

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MICRO MAGIC 2014 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info