Bedienungsanleitung Graupner MX-16 HoTT (Seite 39 von 200) (Englisch)

467107

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

Using the transmitter for the ﬁrst time - Updating the ﬁrmware

ently using them incorrectly. This means that any

servos connected to these channels will simply

“stay put” at their centre position until a trans-

mitter control is assigned to the channel in ques-

tion. For the same reason virtually all the mixers

are inactive by default. For more details of this

please refer to page 86 (ﬁxed-wing model) or 88

(helicopter).

The basic procedure for programming a new •

model memory can be found on page 66, and in

the programming examples starting on page 164.

When switching on, binding or setting up the ra-•

dio control system, please ensure at all times

that the transmitter aerial is an adequate distance

from the receiver aerials. If the transmitter aeri-

al is too close to the receiver aerials, the receiver

will be swamped, and the red LED on the receiv-

er will begin to glow. At the same time the down-

link channel will stop working. As a result the

ﬁeld strength bars on the transmitter screen are

replaced by “x”, and the receiver battery voltage

is displayed as 0.0 V. At the same time the radio

control system switches to Fail-Safe mode, see

page 136, i.e. the servos remain ﬁxed in their cur-

rent position for as long as reception is not pos-

sible, and until a new, valid signal is picked up.

If this should happen, simply increase the dis-

tance between transmitter and receiver until the

displays revert to “normal”.

Updating the transmitter ﬁrmware

The transmitter ﬁrmware can be updated at the owner’s

risk using either of two methods:

As described under “FIRMWARE UPDATE / Chang-•

ing the screen language” in the section entitled

“Hidden mode” on page 27.

As described in the next section, using the ﬁve-pin •

mini-USB port on the back of the transmitter, in

conjunction with a PC or laptop running Windows XP,

Vista or 7.

Current software and information can be found in the

Download section for the corresponding product at www.

graupner.de.

Note:

Once you have registered your transmitter at https://

www.graupner.de/en/service/product_registration you

will automatically be informed of new updates by e-mail

as they become available.

The easiest method of accessing the “corresponding”

product page, as mentioned above, is to enter www.

graupner.de in the address line of your Internet browser,

and then press the ENTER button of your PC or laptop:

This takes you to the home page of the Graupner com-

pany website, where you will ﬁnd an input ﬁeld at top

right below the title “Suchen / Search”:

Place the mouse pointer in this ﬁeld and then enter a

search term, for example, the article number printed on

the type placard on the back of your transmitter:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX-16 HoTT Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX-16 HoTT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info