Bedienungsanleitung Graupner MX-16 HoTT (Seite 47 von 200) (Englisch)

467107

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

Updating the receiver ﬁrmware

When you have called up the program, you will see

the number “1” ﬂashing red in the numeric row 1 … 5

at the top of the window, indicating that the program

is currently operating at “[Process Step] 1”.

In each case the meaning of the currently ﬂashing

step is indicated immediately below the numeric row:

For example, at Step 1: “Connect USB lead to HoTT

receiver” and “Press File Browse button and select

Update ﬁle”, as shown here.

Note:

At any time you can call up an explanation of any

step in the form of Quick-Info by positioning the

mouse pointer over a number.

If you have not already done so, connect your receiv-

er to the PC or laptop at this point. Now click on the

button marked “File Browse” and select the ﬁrmware

update ﬁle matching your receiver in the “Open ﬁle”

dialogue which now appears; the ﬁle sufﬁx will be

“bin”.

In the case of the zip ﬁle “HoTT_Software_VX” which

you have already downloaded and unpacked, this

will usually be found in the folder whose name starts

with the Order Number of the receiver to be up-

dated. If your receiver is the GR-16 which is sup-

plied in the set as standard, this would be the folder

“33508_8CH_RX”. The ﬁle appears in the associated

window. At the same time the “2” starts to ﬂash red:

Note:

The ﬁrmware ﬁles are encoded in a manner speciﬁc

to each product, i.e. if you accidentally select a ﬁle

which does not match the product (e.g. transmitter

update ﬁle instead of receiver update ﬁle), the pop-up

window “Product code error” appears, and you will be

unable to continue the update process.

Follow the instructions for “[Process Step] 2”. With

the receiver still switched off, click on the “Download

Start” button in the “HoTT Receiver Upgrade” window.

(The display changes to “[Process Step] 3”.) Wait un-

til the progress bar starts to advance; this may take

several seconds, depending on your computer.

Only at this point should you switch the receiver on

with the SET button pressed in. After a few seconds

“Line 3” appears in the column “No” of the Status dis-

play, with the message: “Found target device …”. Re-

lease the button at this point. The actual ﬁrmware

update process now starts automatically: “11, Start

Firmware upgrade…”.

If the device is not detected, a pop-up window ap-

pears with the message “Target device ID not found”.

If this should happen, check your update arrange-

ments and try again:

In the Status display the progress of the ﬁrmware up-

date is indicated by the progress bar.

During the update process the green and the red

LED on the receiver glows a constant green and red.

You must not interrupt the connection between

the transmitter and the PC during the update

process!

The update is ﬁnished when the progress bar reach-

es the right-hand end, and the message “12, Com-

plete !!” appears in the bottom line of the Status dis-

play. At the same time the [Process Steps] display

moves on to “5”.

When the update is completed, the green LED goes

out, and the red LED starts to ﬂash.

If the process terminates before the 100% mark is

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX-16 HoTT Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX-16 HoTT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info