Bedienungsanleitung Graupner MX-16 HoTT (Seite 79 von 200) (Englisch)

467107

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

Program description: base settings - ﬁxed-wing model

switches assigned to phase 3 or 4 is also closed, or

phase 3, if the switches assigned to phases 3 and 4

are closed.

As a result you may wish to take the inherent phase •

priorities into account when assigning names to the

ﬂight phases; see below.

At the servo end the transition does not occur •

“abruptly”, but with a ﬁxed transition period of about

one second.

Programming

When you select “phase 2”, “phase 3” or “phase 4” using

the arrow buttons  of the left or right-hand touch-

key, the “Name” ﬁeld for that ﬂight phase is already

framed.

If the default name does not seem appropriate, touch

the central SET button of the right-hand touch-key, and

the current setting is shown highlighted. Now use the

arrow buttons of the right-hand touch-key to select an

appropriate name from those available. Touch the SET

button to conclude the input process.

Now press the  button of the left or right-hand touch-

key to move to the right-hand column at the bottom of

the screen, indicated by the switch symbol

, and

brieﬂy touch the central SET button. You can now assign

a switch to the phase as described on page 57. We

recommend one of the two three-position switches SW

4/5 or SW 6/7, in each case starting from the centre

toggle position.

For more information on ﬂight phase programming

please refer to page 106, in the section entitled “Phase

trim”.

Receiver output

For maximum ﬂexibility in terms of receiver socket

assignment, the mx-16 HoTT software provides the

means to swap over the servo outputs 1 to max. 8;

this is carried out on the second page of the “Receiver

output” sub-menu.

10:01 2

phase 2

phase 3

phase 4

takeoff

landing

speed

–––

timer

receiv out

Touch the central SET button of the right-hand touch-key

to move to the next page of the display. Here you can

assign the “control channels” for servos 1 … 8 to any

receiver output you wish to use. However, please note

that the display in “Servo display” - which you can ac-

cess from virtually any menu position by simultaneously

touching the  and  buttons of the left-hand touch-

key - refers exclusively to the “control channels”, i. e. the

outputs are NOT swapped over.

output

Use the arrow buttons  of the left or right-hand

touch-key to select the servo / output combination you

wish to change, then touch the central SET button of the

right-hand touch-key. Now you can assign the desired

servo (S) to the selected output using the right-hand

arrow buttons, and conﬁrm your choice with SET … or

alternatively touch the  or  buttons of the right-

hand touch-key (CLEAR) simultaneously to revert to the

default sequence.

Please note that any subsequent changes to servo

settings, such as servo travel, Dual Rate / Expo, mixers

etc., must be carried out according to the original

(default) receiver socket sequence.

Note:

It is also possible to distribute the control functions

amongst as many receivers as you wish, using the

channel-mapping function in the mx-16 HoTT’s inte-

gral Telemetry menu, or even to assign the same control

function to multiple receiver outputs. For example, you

might wish to actuate each aileron with two servos in-

stead of just one, etc. However, we strongly recommend

that you use only one of the two options, as a combina-

tion will soon lead to confusion.

rx bind

Graupner|SJ HoTT receivers have to be “instructed” to

communicate exclusively with a particular model (i. e.

model memory) of a Graupner|SJ HoTT transmitter. This

process is known as “binding”, and is only necessary

once for each new combination of receiver and model. It

can be repeated at any time.

Important note:

When carrying out the binding procedure, please

ensure that the transmitter aerial is always an

adequate distance from the receiver aerials: keeping

the aerials about 1 m apart is safe in this respect.

Otherwise you risk a failed connection to the down-

link channel, and consequent malfunctions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX-16 HoTT Seite 79

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX-16 HoTT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info