Bedienungsanleitung Graupner MX-16 HoTT (Seite 148 von 200) (Englisch)

467107

148

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

148

Program description: Telemetry menu

SUMI (Sum signal IN).•

RX SERVO TEST

ALL–MIN : 1000µsec

ALL–MAX : 2000µsec

ALARM VOLT : 3.8V

ALARM TEMP–:–10°C

ALARM TEMP+: 55°C

TEST : START

CH OUT TYPE:SUMI

Note that the signal only ever moves in one direction:

towards the SUMI.

However, if reception fails, the receiver deﬁned as

SUMI only uses the sum signal coming from the

SUMO if at least one channel at the SUMI is pro-

grammed to Fail-Safe.

If the receiver programmed as the satellite (SUMO)

suffers signal reception failure, the servos connected

to that receiver take up the Fail-Safe positions pro-

grammed in the satellite receiver, regardless of the

primary receiver.

If, in contrast, reception fails at both receivers simul-

taneously, then the receiver software (the version

current at the time of printing these instructions) al-

ways reverts to the SUMO’s fail-safe settings. Howe-

ver, mutual interactions can certainly not be ruled

out in individual cases, and for this reason we ur-

gently advise you to carry out appropriate tests

BEFORE ﬂying a model.

This receiver conﬁguration is recommended in partic-

ular circumstances: for example, if one of the two re-

ceivers has to be installed in an unfavourable position

in the model, or if there is a danger that the received

signal will be weak in certain ﬂight attitudes, per-

haps due to a turbine, carbon ﬁbre in the airframe, or

a similar problem, with the result that sporadic range

problems might be expected.

For this reason it is essential to connect the most im-

portant control functions to the primary receiver (the

one programmed as SUMI), so that interference to

the satellite receiver (SUMO) does not cause the

model to go out of control.

Telemetry data, such as the voltage of the airborne

power supply, are only sent to the transmitter by the

satellite receiver (conﬁgured as SUMO), i. e. all te-

lemetry sensors must be connected to the satellite

receiver (SUMO).

Each receiver should be connected to the shared

power supply using its own power lead. If high cur-

rents can be expected, duplicated power connec-

tions are recommended. However, if each of the two

receivers is to be pow-

ered by its own bat-

tery, then it is essential

to withdraw the cen-

tral (red) wire from one

of the two satellite lead

connectors, as shown

in the illustration.

If you wish to carry out further programming, such

as the Fail-Safe settings, disconnect the three-core

satellite connection between the two receivers, and

switch on just the receiver you wish to address. Note

that you may also need to change the binding se-

quence.

Setting up / displaying sensor(s)

If you select at least one sensor in addition to “Receiver”

in the “SELECT SENSOR” sub-menu of the “Telemetry”

menu, which is described below, then you can read

red

out and alter its settings following on from the receiver

pages described in the previous sections.

However, if you wish to have actual access to these

data, then you must connect the selected sensor or

sensors to a receiving system, and set up a working

tele metry link. If you activate at least one sensor, as

described in the next section, you can switch directly be-

tween the individual modules - provided that the sensor

is loaded with the current ﬁrmware. However, if you are

using sensors with earlier ﬁrmware, it may be necessary

to select “etc.” instead of selecting the sensor directly.

In either case press the Select button  or  of the

left-hand touch-key …

RECEIVER

etc.

VARIO

… and then select the desired module using the same

buttons, working either up or down, e.g.:

GENERAL

RECEIVER

ELECT. AIR

If the General Module is active, as selected in our exam-

ple, you will also see the right-pointing arrow “ ” at top

right on the last receiver page (“RX SERVO TEST”), in

addition to the left-pointing arrow “ ”; this indicates that

further screen pages are available:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX-16 HoTT Seite 148

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX-16 HoTT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info