Bedienungsanleitung Graupner MX12 (Seite 29 von 48) (Englisch)

30127

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Ch6 = Pitch

3 servo (120°)

Ch2 = Aileron

Ch2 = Elevator

Ch6 = Pitch

Throttle Cut Switch

This function assigns the Throttle Cut switch to the push

button located on upper right front of the transmitter.

The Throttle Cut function is designed to return the

throttle trim to the lowest position instantly and keep this

position while the button is pressed. This feature is used

to “cut“ or stop the engine without changing the position

of digital throttle trim.

Function mode HELICOPTER

Throttle Cut Switch; Throttle Hold

Function mode HELICOPTER 29

Throttle Cut Operating position

(-32~-128)

Go to Throttle Hold

Go to Travel adjust

Change value

Set function to Inhibit

Accessing the Throttle Cut Function

1. Place the transmitter power switch in the ON positi-

on.

2. Access the Function mode. To do so, press the

Down ans Select keys simultaneously. Press

either the Up or Down key until THRO CUT ap-

pears in the upper portion of the LCD screen.

3. Us the (+) and (-) keys to change the value of the

Throttle cut function.

Note: Pressing the Clear key will Inhibit the Throttle

Cut, turning it off until it has been reactivated.

4. Access the TRAVEL ADJ mixing function by pres-

sing the Down key.

5. Access the THROTTLE HOLD function by pressing

the Up key.

6. Exit the THRO CUT function by pressing the Down

and Select keys simultaneously.

Throttle Hold

The Throttle Hold function is designed to hold the thrott-

le servo in a specific position during an autorotation.

This is very useful for practicing autorotation landings.

The throttle hold switch can be programmed to one of

the four toggle switches. Throttle hold will always be

“On“ in the forward switch position and “Off“ in the rear

position.

Press +/- key Press CLR key during selecting

Go to Throttle Curve

Go to Throttle Cut

Select function to

change

Change value/SW

selection

Reset POS value to 0

or Inhibit function

Throttle Hold Position

(-20~50)

Hold SW Select

Switch

LEFT : THRO HOLD SW Forward SideOn

AILE D/R : AILE D/R: AILE D/R SW Position 1On

ELEV D/R : ELEV D/R Position 1On

RIGHT : FLIGHT MODE SW Forward SideOn

Accessing the Throttle Hold Function

1. Place the transmitter power switch in the ON positi-

on.

2. Press the Down and Select keys simultaneously

to enter the Function mode.

3. Press either the Up or Down key until THROTTLE

HOLD appears across the top of the LCD.

4. The factory setting for the throttle hold is inhibit.

Pressing either the (+) or (-) key will activate Throttle

Hold and display the current throttle hold value.

5. Using the (+) or (-) key, adjust the throttle hold

value to deliver the proper engine idle rpm for your

helicopter. The adjustable range is (-20% -/+ 50%).

Once you establish the proper idle value for your

engine, you can use this value for throttle hold as

well. To shut the engine off for autorotation, a negati-

ve or zero value should be input.

Note: When the throttle hold is activated, and the

switch is on, the indicator on the LCD will

change from Off to On. In addition, the throttle

trim indicator will be inhibited.

6. Access the THROTTLE CURVE function by pres-

sing the Up key.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX12 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info