Bedienungsanleitung Graupner MX12 (Seite 34 von 48) (Englisch)

30127

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Function mode HELICOPTER

Fail Safe

34 Function mode HELICOPTER

SW display

ALWAYS ON: Always Mixing On

RIGHT FWD: Gear SW Forward sideOn

RIGHT REA: Gear SW Rear sideOn

LEFT FWD: FLAP SW Forward sideOn

LEFT REA: FLAP SW Rear sideOn

AILE D/R: AILE D/R SW Position 1On

ELEV D/R: ELEV D/R SW Position 1On

Accessing the Programmable Mixing Function

1. Place the transmitter power switch in the ON positi-

on.

2. Press the Down and Select keys simultaneously

to enter the Function mode.

3. Press either the Up or Down key until MIX 1 ap-

pears in the LCD.

Selection the Master and Slave Mixing Channels

4. Press the (+) or (-) keys to select the master chan-

nel.

5. Press the Select key to move the cursor to the

slave channel.

6. Press the (+) or (-) keys to select the slave channel.

7. Press the Select key once. The display will conti-

nue to show the current mixing channels at the

top of the LCD, but now an arrow will indicate the

current stick position (master) to be adjusted.

Setting the Mixing Values

8. While holding the master stick in the direction you

want to mix, press the (+) or (-) keys to increase or

decrease the mixing value for the slave channel. The

value in the LCD will change to display the current

mix value selected. Next, hold the master stick to the

other side to adjust the mix for the other direction.

Setting the Mixing Switch Activation

9. Press the Select key until the SW is highlighted.

The LCD with “ALWAYS ON“ indicates the current

switch that this mix currently selected to always be

active (ON).

Mixing Operation and Switches

Each mixing program can be turned on and off by a

lever or switch. The lever and switches that can be

selected for program mixing are tabulated at the right

with their abbreviations appearing on the display and

their corresponding positions.

Setting the Mixing Channel Offset

1. Press the Select key until offset is highlighted. The

display will show the current mixing channels at the

top of the LCD, with the word “OFFSET“ in the

center of the LCD. The value to the right is the

mixing Offset neutral point, currently 0.

2. A new value for the offset can be selected using the

(+) or (-) keys. This is the new neutral point for the

slave channel (Point that the mix is activated). Press

the Clear key to reset the value back to 0.

3. Press the Down and Select keys simultaneously

to exit the Programmable Mix function.

With a little practice, programmable mixing will become

easier to understand. Mixing is only limited by your

imagination.

Fail Safe

The Fail Safe Function is available only when you use

the mx-12 transmitter in PCM modulations. This function

is designed to help minimize damage to your aircraft

during a loss of signal to the receiver. The servos either

assume the Fail Safe presets or hold their last good

signal position.

As noted earlier, if you are in the PPM modulation, the

Fail Safe Function is not applicable. Therefore, the Fail

Safe Function will not appear on your LCD screen menu

while in the PPM mode. Refer to the Modulation Selec-

tion section for more information pertaining to the

broadcast signal of you mx-12 transmitter.

Note: The throttle Fail Safe position is defaulted to the

idle position for added safety.

Channel beeing programmed

TH : Throttle

AI : Aileron

EL : Elevator

RU : Rudder

GE : Gear

PI : Pitch

Go to Fail Safe menu

Go to Revolution

Mixing menu

Change highlighted

selection

Change selected

value

Reset selection to

default

Accessing the Fail Safe Function

1. Place the transmitter power switch in the ON positi-

on.

2. Access the Function mode. To do so, press the

Down and Select keys simultaneously. Press

either the Up or Down key until FAIL SAFE ap-

pears in the upper portion of the LCD screen.

3. Use the Select key to highlight the servo function to

set.

4. Use the (+) or (-) keys to toggle between servo hold

or setting the servo position.

5. When using the servo setting position, move the

corresponding control stick to the position where you

want the servo if the radio enters into the fail safe

mode. Press the Clear key to have the transmitter

memorize the stick position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX12 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info