Bedienungsanleitung Graupner XG-6i (Seite 16 von 30) (Deutsch, Englisch, Französisch)

637243

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

05 94001 GM-Racing XG-6i Race Spec Instructions

English

5. EXPONENTIAL FUNCTION STEERING (ST CURV)

This function is used to change the sensitivity of the steering servo around the neutral positi-

on. It has no effect on the maximum servo travel. Note: When the setting is not determined,

or the characteristics of the model are unknown, start with 0% ( when EXP is set to 0%, servo

movement is linear).

1. Press “ENTER” to see FUNCTION MENU.

2. Use the +/- Keys to select the ST CURV function and press ENTER.

3. Use the +/- Key to change the value.

4. Press EXIT to save and return to FUNCTION MENU, press EXIT again to return to

the Main Screen.

STEERING CURVER adjusting value range: -100%~+100% Default is 0% (Linear)

STEERING EXP ADJUSTMENT

1. When you want to quicken steering operation, use the (+) button to adjust the

+ side. When you want to make steering operation milder, use the (-) button to adjust

the -side.

2 . When ending setting, return to the function menu by pressing the (EXIT) button .

TERMS: M-MODE, R--RATE

6. THROTTLE CURVE (TH CURV)

This function makes the throttle high side and brake side direction servo operation

quicker or milder. It has no effect on the servo maximum operation amount. For the high side,

selection from among three kinds of curves (EXP/VTR/CUR) is also possible.

Note: When the course conditions are good and there is no sense of torque at the power

unit, set each curve to the + side (quick side). When the road surface is slippery and

the drive wheels do not grip it, set each curve to the - minus (mild) side. Note: Brake side

only has EXP curves.

1. Press “ENTER” to see FUNCTION MENU

2. Use the +/- Keys to select the TH CURV function and press ENTER.

3. Press ENTER to select a setting.

4. Use the +/- Key to change the value.

5. Press EXIT to save and return to FUNCTION MENU, press EXIT again to return to the

Main Screen.

ADJUSTMENT METHOD FOR EXP CURVE

Select EXP at setup item “M”, select setup item “R” and make the following adjustments:

Forward side adjustment:

Use the (+) button to adjust the + side when you want to quicken the rise and use the(-)

button to adjust the - side when you want to make the rise milder.

Brake side adjustment:

Select the setting item „BR“ by ENTER button and use the (+) button to adjust

the + side when you want to quicker the rise and use the (-) button to adjust the - side

when you want to make the rise milder.

3. When ending setting, return to the initial screen by pressing the EXIT.

TRIM ADJUST

Please start the motor or the engine while making the adjustment of these settings.

1 . Connect the receiver, servos, and other components and then turn on the power swit-

ches to transmitter and receiver.

2. Be sure the Steering trim and Throttle trim on the transmitter are at their neutral positi-

on.

3. When turning on the transmitter, please make sure the transmitter antenna is complete-

ly extended. Turn on the transmitter before turning on the receiver, while turn off the re-

ceiver before turning off the transmitter.

Steering Trim (ST.TRIM):

Steering neutral adjustments can be made by moving the steering trim knob to the left or the

right.

Racers Tip:

Always check and be sure the servo is at its neutral position before installing a ser

vo.

Adjust

the servo horn hole position and linkage so both are parallel. When a servo saver is used

94001 GM-Racing XG-6i Race Spec Instructions 14

English

20. TIMER

Use the timer by selecting one of the two timers UP TIMER and DOWN TIMER, and if the

MODE is INH, It will close the TIMER Function.

1. Press “ENTER” to see FUNCTION MENU

2. Use the +/- Keys to select the TIMER function and press “ENTER”.

3. Press ENTER to select a item.

4. Use the +/- Keys to change the value

5. Press “EXIT” twice to save and return to FUNCTION MENU, press “EXIT” again

to return to the Main Screen

UP TIMER function

Press “ENTER” to select the MODE. Use +/- Keys to select UP_T. (UP TIMER).•

The UP TIMER can be used to count the time from 0 minute 0 second to the stop time. •

The stop time is set form from 0 minute 0 second to 99 minute 30 second.

The ﬁ rst start operation will be linked to the throttle trigger.•

The passage of time is announced by sounding of a buzzer each minute after starting.•

The buzzer will sound ‚B-B-B…‘ when the timer is up to the stop time.•

DOWN TIMER function

Press “ENTER” to select the MODE. Use +/- Keys to select DN_T.(DOWN TIMER).•

The DOWN TIMER can be used to count the time from preset time 0 minute 0 second. •

The preset time is set form 0 minute 0 second to 99 minute 30 second.

The ﬁ rst start operation will be linked to the throttle trigger.•

The passage of time is announced by sounding of a buzzer each minute after starting.•

The buzzer will sound ‚B-B-B…‘ when the timer is down to the 0 minute 0 second•

94001-eng.indd Druckbogen 6 von 10 - Seiten (6, 15)94001-eng.indd Druckbogen 6 von 10 - Seiten (6, 15) 19.01.2009 08:02:4719.01.2009 08:02:47

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner XG-6i Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info