Bedienungsanleitung Grohe 27934 (Seite 8 von 76) (Alle Sprachen)

759826

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Steam nozzle installation, see fold-out page II, Fig. [6] to [11].

IMPORTANT NOTE!

Read the technical product information provided with the concealed

mounting sets for the steam nozzle and feeler gauge.

The steam nozzle must be installed in the steambath cubicle at a height

of 50 to 400mm and routed underneath the seats in the room in

a longitudinal direction. Do not direct the steam jet against walls, seats or

other objects. Keep a minimum of 700mm away from the steam nozzle.

Feeler gauge installation, see feeler gauge II, Fig. [12] to [15].

IMPORTANT NOTE!

Read the technical product information provided with the concealed

mounting sets for the steam nozzle and feeler gauge.

Electrical installation

Electrical installation work must only be performed

by a qualified electrician. This work must be carried

out in accordance with the regulations according to

IEC 60364-7-701 (corresponding to VDE 0100 Part 701)

as well as all national and local regulations.

The device must be connected to the mains power supply via an FI switch

(maximum release current 30 mA). The power supply for the steam

generator must be established via a socket connected directly to the

mains fuse box, see fold-out page I, Fig. [5]. Unobstructed access to

the socket must be guaranteed after installation. No switches should

be connected to this cable. See also section "Automatic drainage".

Check that the electrical socket used is earthed!

Switch on the main switch and check whether smoke emerges.

Main switch

There is an on/off switch at the base of the steam generator that should

only be actuated if the device has not been used for a long time. The

device is not drained automatically when disconnected from the

power supply!

Ventilation

Steambath cubicles do not generally require special ventilation if operated

for less than two hours.

In steambath rooms that operate continuously for more than two hours,

the air must be changed at a rate of 10-20m³ per person per hour for

hygiene and functional reasons.

Any clear space above the steambath cubicle must not be closed off.

Drill or cut a ventilation opening (1000mm²) into the wall where the door

is located to ventilate the cavity above the steambath cubicle.

The air inlet consists of an opening in the door wall near to the floor or

a gap under the door.

The air outlet must be integrated at the very top of the wall or in the

ceiling and should be positioned as far away from the air inlet as possible.

However, it should not be positioned above the door or directly above one

of the seats. The outlet is connected to an air duct that leads outside.

An existing air duct can be used. The duct must be completely steam and

watertight and designed to withstand the high degree of moisture in the

air. Bends that allow the formation of "pockets of condensate" which affect

the function of the duct are not permitted. If pockets of water are

unavoidable, a water separator must be installed to drain the condensate.

The air outlet must be large enough to discharge 10–20m³ of air per

person per hour.

Mechanical ventilation. If the air does not escape quickly enough by

itself, e.g. through negative pressure in the room where the steambath

cubicle is located, a ventilator must be installed. The fan must be set to

extract a minimum of 10m³ and a maximum of 20m³ of air per person per

hour.

Automatic drainage

This automatic control considerably reduces the accumulation of calcium

carbonate and other deposits in the water tank. If there is a switch in the

cable between the power supply and the steam generator, it can only be

actuated 110 minutes after the system is switched off so that the water

tank can drain and flush automatically. It is therefore important that a faulty

electrical connection does not render inoperative the automatic drainage

function on the steam generator.

WARNING! The water is hot!

Descaling

Regular descaling is important because it extends the service life of the

steam generator and ensures that it functions correctly. Descaling

removes limescale deposits from walls and heating elements. The user

has the option of descaling automatically after 130 hours of operation

(preset interval) or descaling manually before the 130 hours elapse.

The descaling time is displayed on the control panel of the terminal

device. The steam generator is disabled when the time elapses.

Additional instructions on how to use the app

and activate the functions can be downloaded at

www.grohe.com/tpi/f-digital-deluxe.

1.Start the steam generator and allow to operate until the water in the

container starts to boil.

Hot steam may escape from the steam outlet.

The steam generator stops after 20 minutes. The heating phase for

descaling is complete.

2.Unscrew the cap nut from the three-way coupling at the top of the steam

generator.

Caution hot! Protect against burns!

3.Pour two 80g packs of descaling agent into the container via the three-

way coupling using a funnel (Prod no.: 14 015 000).

4.Screw the cap nut back onto the three-way coupling.

After approx. 1,5 hours, the container is drained and flushed

clean automatically. The steambath cubicle must not be

used during this time period.

5.Reset the timer for the descaling interval as described in the Grohe SPA

app operating instructions.

Please pass these instructions on to the fitting user!

The right to make technical modifications is reserved!

Grohe 27934 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info