Bedienungsanleitung Grohe 38778 Tectron (Seite 9 von 16) (Deutsch, Englisch)

759441

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Final installation

Preparations

Cistern A, see fold-out page II, Figs. [5 - 13]:

1. Remove structural shell protection (K1) from the cistern,

see Fig. [5].

2. Feed extension cable (L) through vacant tube (B) into the

cistern and connect to transformer (A), see Fig. [6].

3. Close shut-off device (N), see Fig. [7].

4. Replace existing hose with hose with elbow (O) (scope of

delivery), open shut-off device (N).

5. Fasten lift rod (P) to overflow pipe, see Fig. [8].

6. Engage servo motor (V) in retaining plate (V1), see Fig. [9].

7. Cut off the right tab of bracket (Q), see fig [10].

8. Detach foil from adhesive strip (Q1) and fasten electronic

module (C) to bracket (Q), see Fig. [11].

Note: Button (C2) of the electronic module must be on the left.

9. Fasten bracket (Q) to frame (R) using screws (R1) and

nuts (R2), see Fig. [12].

Note: Select the correct frame (by comparing with the frame in

the cover plate delivery specification)

10.Locate frame (R), align and fasten to cistern using washers

and long screws (U), see Fig. [13].

Cistern B, see fold-out page II and III, Figs. [14 - 22]

1. Cut off structural shell protection (K2) flush with the tile

surface, see Fig. [14].

2. Feed extension cable (L) through vacant tube (B) into

cistern and connect to transformer (A), see Fig. [15].

3. Detach the overflow pipe (S) from the waste valve, see

Fig. [16].

4. a)Water connection centre or right:

Pull out waste (S), turn through 180° and reengage, see

Fig. [17a].

Cut off the right tab of bracket (Q).

Fasten lift rod (P) to overflow pipe (S1) and fasten the

overflow pipe to the waste.

b)Water connection left:

Cut off left tab of bracket (Q), see Fig. [17b].

Fasten lift rod (P) to overflow pipe (S1) and fasten the

overflow pipe to the waste.

5. Close shut-off device (N), see Fig. [18].

6. Replace existing hose with hose with elbow (O) (scope of

delivery), open shut-off device (N).

7. Engage servo motor (V) in bracket (V2), see Fig. [19].

8. Detach foil from adhesive strip (Q1) and fasten electronic

module (C) to bracket (Q), see Fig. [20].

Note: Button (C2) of the electronic module must be on the left.

9. Fasten bracket (Q) to frame (R) using screws (R1) and

nuts (R2), see Fig. [21].

Note: Select the correct frame (by comparing with the frame in

the cover plate delivery specification)

10. Fit frame (R), align and fasten to structural shell protection

using short screws (T), see Fig. [22].

Calibrating the servo motor

Note: The servo motor must be calibrated outside the cistern.

1. Connect the voltage supply: Connect the electronic

module (C) with the extension cable (L), see fold-out

page III, Fig. [23]. The servo motor must not be connected

when performing this operation.

2. The LED (C1) in the electronics begins to flash.

3. Connect servo motor (V) to electronic module (C), see

Fig. [24].

The LED in the electronics ceases to flash and adjustment

automatically starts once the servo motor has been

connected to the electronics. The servo motor moves to the

adjustment positions.

Note: It must be ensured that the movement is not disrupted

by obstacles.

To prevent falsification of the servo motor adjustment,

lever (V3) must not be removed.

Calibration has been completed when lever (V3) is at

approx. 90° and the LED in the electronics does not flash,

otherwise see section: Fault / cause / remedy.

Note: Do not disconnect the servo motor from the electronic

module following calibration.

Installing the servo motor

Cistern A, see fold-out page III and IV, Figs. [25 - 27]

1. Disconnect electronic module (C) from extension cable (L),

see Fig. [25].

2. Engage retaining plate with servo motor (V) in the

bracket (W) in the cistern, see Fig.[26a].

3. Clamp pneumatic hose (S2) in the groove of the retaining

plate (V1).

4. Insert lift rod (P) through opening in lever (V3) from the rear,

see Fig. [27].

5. Connect the voltage supply: connect electronic module (C)

and extension cable (L).

6. Make settings.

Cistern B, see fold-out page III and IV, Figs [25 - 27]

1. Disconnect electronic module (C) from extension cable (L),

see Fig. [25].

2. Engage servo motor (V) in crossrail (Y) in the cistern, see

Fig. [26b].

Note: The servo motor must be fastened to the side of the

crossrail which is opposite the filler valve.

3. Clamp pneumatic hose (S2) in the groove of the

crossrail (Y).

4. Insert lift rod (P) through opening in lever (V3) from the rear,

see Fig. [27].

If the servo motor is located on the left side of the crossrail,

insert the lift rod through the opening in lever from the front.

5. Connect the voltage supply: connect electronic module (C)

and extension cable (L).

6. Make settings.

Installing the plate

1. Push the extension cable into the vacant tube until the plug

connection no longer protrudes into the cistern.

2. Connect pneumatic hose (S2) to the actuation plate, see

Fig. [28].

3. Install plastic plate, see Fig. [29a].

Install metal plate, see Fig. [29b].

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grohe 38778 Tectron Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info