Bedienungsanleitung Grouw 17937 (Seite 59 von 165) (Deutsch, Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

788793

Zoom out

Zoom in

Vorherige Seite

1/165

Nächste Seite

Boundary cut

The robot lawnmower is programmed at the factory to

automatically run along the boundary wire and cut the

grass once a week.

*Depending on software version.

Changing the PIN code

1. Switch the robot lawnmower on as described above

so that the on/locked indicator light (j) lights up

green.

2. Press the LOCK/4 (e) and OK (f) buttons at the same

time. The on/locked indicator light ashes green and

red.

3. Enter a new 4-digit PIN code using the 1-4 buttons (b,

c, d, e) and then press the OK button. The on/locked

indicator light ashes green.

4. Enter the same PIN code again and press the OK

button. The on/locked indicator light lights up green.

The PIN code has now been changed.

5. Keep in mind that the PIN code is an eective anti-

theft measure! If you forget your PIN code, you

cannot unlock the control panel or use the robot

lawnmower!

If you forget your PIN code, you must visit www.schou.

com and follow the instructions on obtaining a new

PIN code. For this, you will need the robot lawnmower’s

serial number and the purchase receipt.

Updating the rmware

Note!

• Therobotlawnmowermustbepositionedwithinits

working area once the update is complete.

• Thermwareupdatemustbeperformedwithafully

charged battery.

• Donottouchthemainswitchduringthermware

update.

1. Download the rmware update from www.grouw.

dk or www.schou.com. You can also read the update

instructions there. Copy the rmware update onto an

empty USB stick (max. 4 GB, not supplied), which is

FAT32 formatted. Double-click on start.bat to extract

the rmware les.

2. Set the main switch (9) to the OFF position.

3. Insert the USB stick into the USB jack as illustrated.

4. Set the main switch (9) to the ON position. Press the

POWER (a) and OK (f) buttons at the same time. All

the indicator lights light up green.

5. Press the LOCK/4 button (e). The rmware update

starts. When all ve indicator lights for work time (i)

are lit, the update is complete.

The update typically takes 3-5 minutes. If the update

has not started after 1 minute, this is due to incorrect

use or because the USB stick is damaged. Try using a

dierent USB stick.

6. Remove the USB stick and replace the USB cover.

Note!

You can also update the firmware wirelessly via

Bluetooth. Follow the instructions in the Bluetooth

guide.

Rain sensor

The robot lawnmower is equipped with a rain sensor so

that it can detect when it rains. The robot lawnmower is

programmed at the factory to return to the charging

station when it is raining sufficiently to activate the rain

sensor. There it will fully charge and then wait

for another 2 hours after the rain sensor is dry before

automatically starting to cut the grass. If this start time is

outside of the robot lawnmower’s daily work time, it will

not start again until the following working day.

USB

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grouw 17937 Seite 59

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info