Bedienungsanleitung Grouw 17937 (Seite 61 von 165) (Deutsch, Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

788793

Zoom out

Zoom in

Vorherige Seite

1/165

Nächste Seite

Note!

If the error indicator light ashes red on the robot

lawnmower, there is an error in the boundary wire

signal:

• Therobotisoutsidetheboundarywire.

• Theboundarywireistoolong(over250m).

• Theboundarywireisassembledincorrectly,there

is moisture in a joint, or an incorrect connector has

been used.

• TheboundarywiremustNOTbestrippedwhen

using the connector provided.

• Youcanremovetheendsoftheboundarywirefrom

the charging station and measure the resistance

of the boundary wire using a multimeter. A new

boundary wire has a resistance of about 2 Ohm per

100 metres.

If the boundary wire’s resistance measures more

than 8-10 Ohm, the robot lawnmower will display a

boundary wire signal error.

Correct the error or replace the boundary wire.

5) Abnormal battery temperature

The robot lawnmower will report an error if the battery

temperature during operation is outside the range of

0-75 °C or during charging is outside the range of 0-45

°C.

The robot lawnmower returns to the charging station

and lets the battery return to a safe temperature.

The risk of this is greatest in summer, when the outside

temperature in direct sunlight approaches 35 °C. It may

be a good idea to change the start time of the robot

lawnmower so that it starts earlier in the day when it is

not so hot.

6) Battery error

The robot lawnmower reports an error if the battery

is defective. Replace the battery with a new original

battery with the same specications as the defective

battery.

If the battery indicator light lights up red instead,

the battery simply needs charging. Carry the robot

lawnmower to the charging station and manually

charge it.

7) Charging error

The robot lawnmower has returned to the charging

station but it cannot be charged.

Check that the charging poles are clean and are

correctly inserted into the charging socket on the robot

lawnmower.

If the battery is at, you must perform manual charging.

Manual charging

Pull the robot lawnmower out of the charging station.

Move the main switch to the OFF position and wait 5

seconds.

Set the main switch to the ON position and push the

robot lawnmower into the charging station again. Do

NOT switch the robot lawnmower on using the Power

button (a)!

The indicator light on the charging station does not

necessarily change to red immediately if the battery

voltage is very low. It can take up to 1 hour before the

indicator light on the charging station turns red.

When the indicator light on the charging station

lights up green, charging is complete and the robot

lawnmower is fully charged.

8) PCB overheating

The robot lawnmower reports an error if the PCB

overheats. The robot lawnmower returns to the

charging station and allows the PCB to return to a safe

temperature.

The risk of this is greatest in summer, when the outside

temperature in direct sunlight approaches 35 °C. It may

be a good idea to change the start time of the robot

lawnmower so that it starts earlier in the day when it is

not so hot.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grouw 17937 Seite 61

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info