Bedienungsanleitung Grundig GTN 27250M (Seite 38 von 160) (Deutsch)

712282

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

ENGLISH

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

• Young children and the infirm. This appliance is not

intended for use by young children or infirm persons

without supervision. (XE requirement - English only)

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

mental abilities; lack of experience, knowledge or skills

unless they are supervised by a person responsible for their

safety. Children should never be left alone with thisproduct.

Lock-Off Button and Variable Speed Trigger

(Fig. A)

DCS334

To lock the variable speed trigger

1

, press the lock-off

button

2

. When the lock-off button is depressed to the lock

icon, the unit islocked.

Always lock the trigger switch when carrying or storing the tool

to eliminate unintentionalstarting.

To unlock the trigger switch, press the lock-off button. When

the lock-off button is depressed to the unlock icon, the unit

isunlocked.

NOTE: The lock-off button is colored red to indicate when the

switch is in its unlockedposition.

To start the DCS334 jig saw, squeeze the variable speed

trigger

1

To slow and stop the jig saw, release thetrigger.

As the trigger is pressed in, the strokes-per-minute continue

to increase, but up to the maximum speed of the tool. As the

trigger is released, the blade strokes-per-minutereduce.

NOTE: This tool has no provision to lock the switch in the ON

position, and should never be locked ON by any othermeans.

On/Off Switch (Fig. A)

DCS335



CAUTION: Move the on/off switch

1

to the OFF position

before inserting the batterypack.

To start the DCS335 jig saw, move the on/off switch

1

to the

ON position. To turn the jig saw off, move the on/off switch to

the OFFposition.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, depress the trigger lock button and

disconnect battery pack before making any

adjustments or removing/installing attachments or

accessories. An accidental start-up can causeinjury.



WARNING: Use only

DeWALT

battery packs andchargers.

Inserting and Removing the Battery Pack

from the Tool (Fig. C)

DCS335: Move the on/off switch

1

to the OFF position before

inserting the batterypack.

NOTE: Make sure your battery pack

11

is fullycharged.

To Install the Battery Pack into the Tool

Handle

1. Align the battery pack

11

with the rails inside the

tool’shandle.

2. Slide it into the handle until the battery pack is firmly seated

in the tool and ensure that you hear the lock snap intoplace.

To Remove the Battery Pack from the Tool

DCS335: Move the on/off switch

1

to the OFF position before

removing the batterypack.

1. Press the release button

12

and firmly pull the battery pack

out of the toolhandle.

2. Insert battery pack into the charger as described in the

charger section of thismanual.

Fuel Gauge Battery Packs (Fig. C)

Some

DeWALT

battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge button.

A combination of the three green LED lights will illuminate

designating the level of charge left. When the level of charge

in the battery is below the usable limit, the fuel gauge will not

illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end-userapplication.

Blade Installation and Removal (Fig. D, J)

To Install a Blade

NOTE: This jig saw uses only T-shank jig sawblades.

NOTE: The DT2074 flush cutting blade is for use with D

WALT

DCS334 and DCS335 jig sawsonly.

NOTE: When installing flush cutting blades (DT2074), the anti-

splinter insert (

20

, Fig. J) must be removed and the shoe must

to be in the 0° positive stopposition.

NOTE: The correct saw blade must be selected for the material

beingcut.

1. Hold open the blade release latch

4

as shown in FigureD.

2. Insert the T-shank blade into the clamp mechanism

13

while guiding the back of the blade into the groove of the

guide rollers

14

3. The T-shank should be completely inside the

clampmechanism.

4. Release the blade releaselatch.

To Remove a Blade



CAUTION: Do not touch used blades, they may be hot.

Personal injury mayresult.

1. Hold open the blade release latch

4

2. With a slight shake the blade will dropout.

3. Release the blade releaselatch.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grundig GTN 27250M Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info