Bedienungsanleitung Grundig GTN 27250M (Seite 40 von 160) (Deutsch)

712282

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

ENGLISH

OPERATION

Instructions for Use



WARNING: Always observe the safety instructions and

applicableregulations.



WARNING: To reduce the risk of serious personal

injury, depress the trigger lock button and

disconnect battery pack before making any

adjustments or removing/installing attachments or

accessories. An accidental start-up can causeinjury.



WARNING: Always wear proper personal hearing

protection. Under some conditions and duration of use,

noise from this product may contribute to hearingloss.



WARNING: Risk of dust inhalation. To reduce the risk of

personal injury, ALWAYS wear an approved dustmask.



WARNING:

• Make sure your workpiece is well secured. Remove

nails, screws and other fasteners that may damage

theblade.

• Check that there is sufficient space for the blade

underneath the workpiece. Do not cut materials that

are thicker than the maximum cuttingdepth.

• Use sharp saw blades only. Damaged or bent saw

blades must be removedimmediately.

• Never run your tool without a sawblade.

• For optimal results, move the tool smoothly and

constantly over the workpiece. Do not exert lateral

pressure on the saw blade. Keep the shoe flat on the

workpiece. When sawing curves, circles or other round

shapes, push the tool gentlyforward.

• Wait until the tool has come to a standstill before

removing the saw blade from the workpiece. After

sawing the blade may be very hot. Do nottouch.

Proper Hand Position (Fig. L)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires one hand on the main handle

9

Cutting



WARNING: The jig saw should not be operated with the

shoe removed or serious personal injury mayresult.

Pocket Cutting (Fig. M)

A pocket cut is an easy method of making an inside cut. The

saw can be inserted directly into a panel or board without first

drilling a lead or pilot hole. In pocket cutting, measure the

surface to be cut and mark clearly with a pencil. Next tip the saw

forward until the front end of the shoe sits firmly on the work

surface and the blade clears the work through its full stroke.

Switch the tool on and allow it to attain maximum speed. Grip

the saw firmly and lower the back edge of tool slowly until the

blade reaches its complete depth. Hold the shoe flat against the

wood and begin cutting. Do not remove blade from cut while it

is still moving. Blade must come to a completestop.

Flush Cutting (Fig. N)

A flush cut is necessary when finishing off cuts up to a wall or

an obstacle, such as back-splash. One of the easiest ways to

accomplish the flush cut is to use a flush cutting blade (DT2074).

The flush cutting blade provides the reach necessary to cut

right up to the front edge of the jig saw shoe. Remove the

anti-splinter insert and return the shoe to the 0° positive stop

position before installing and using the flush cutting blade. For

the best cut quality the flush cutting blade should be used in

the 0 or 1 orbital position. The flush cutting blade should not be

used to start the cut because the flush cutting blade prevents

the shoe from being supported by the work surface. Use wood

cutting practices explainedbelow.

Wood Cutting

Support the workpiece adequately at all times. Use the higher

speed setting for cutting wood. Do not attempt to turn the tool

on when blade is against material to be cut. This could stall the

motor. Place the front of shoe on the material to be cut and hold

the jig saw shoe firmly against the wood while cutting. Don’t

force the tool; let the blade cut at its own speed. When the cut

is complete, turn the jig saw off. Let blade come to a complete

stop and then lay the saw aside before loosening thework.

Metal Cutting

In cutting thin gauge sheet metals, it is best to clamp wood to

the bottom of sheet metal; this will insure a clean cut without

the risk of vibration or tearing of metal. Always remember to use

a finer blade for ferrous metals (for those that have a high iron

content); and use a coarser blade for non-ferrous metals (those

that do not have an iron content). Use a high speed setting

for cutting soft metals (aluminum, copper, brass, mild steel,

galvanized. pipe, conduit sheet metal, etc.). Use lower speed to

cut plastics, tile, laminate, hard metals, and castiron.

MAINTENANCE

Your

DeWALT

power tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regularcleaning.



WARNING: To reduce the risk of serious personal

injury, depress the trigger lock button and

disconnect battery pack before making any

adjustments or removing/installing attachments or

accessories. An accidental start-up can causeinjury.

The charger and battery pack are notserviceable.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grundig GTN 27250M Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info