Bedienungsanleitung Gude 300-10-50 DG 14 TLG 71126 (Seite 12 von 51) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

621510

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

may be accelerated to a great extent by air flow and

thus become a dangerous shot.

 Always use protective equipment against electric

shock

Never use the compressor near water or in a humid

environment.

 Put properly the compressor out of operation

Disconnect the compressor from power source and

release all pressure from the air jet before repair,

inspection, maintenance, cleaning or replacement of

construction parts.

 Unintentional switching on

Do not transfer the compressor when connected to

power source or when the air jet is under pressure.

Before connecting the compressor to power source

make sure the pressure transducer switch is in the

OFF position.

 Proper compressor storage

When the compressor is not in use it is necessary to

disconnect it from power source, store it at a dry

place protected against climatic influences. Keep it

out of reach of children.

 Working clothes

Do not wear wide clothes or jewellery as they can

get caught by machine parts.

 Careful compressor maintenance

It is necessary to follow the lubrication

instructions (see the throat for oil adding and oil

level inspection in the "Handling" chapter).

It is necessary to follow instructions concerning

protective cover in the air filter described in the

"Handling" chapter.

Check regularly the power cord. If damaged it needs

to be repaired or replaced in the service repair

centre. Make sure there is no outer visible damage

of the compressor. In case of need, please contact

the nearest repair centre.

 Outdoor use

If use the compressor outside it is allowed to use

extension cables designed for outdoor use and with

appropriate marking only.

Attention: It is necessary to use a cable with

sufficient cross section (min. of 1.5 mm

); at

cables longer than 10 m there may be starting

problems at unfavourable temperatures.

 Attention

Work considerately and use common sense. Do not

use the compressor if you are tired, impaired or

intoxicated with drugs causing tiredness.

 Check faulty and untight construction parts

If there has been any damage to any protective

device or other constructional elements it is

necessary to check the compressor before restarting

in order to ensure its safe operation.

All damaged constructional elements need to be

repaired in the customer service centre or replaced

as described in the operating instructions of the

device.

 Correct compressor using

Follow all instructions mentioned in these operating

instructions at operating the compressor. Prevent children or

persons not familiarised with the manner of working of the

compressor from using it.

 Keep the cowl screen clean

Keep the engine cowl screen clean. Clean the screen

regularly if you operate the compressor in an environment

with severe pollution.

 Operate the compressor at rated voltage

Operate the compressor at voltage specified on the type

label. If the compressor is operated at voltage higher than

the specified rated voltage inadmissible engine overheating

may occur.

 Do not let the device running unattended

 Do not use the compressor when faulty

If there are any strange sounds, strong vibrations at the

compressor or it seems to be faulty in other way it needs to

be stopped immediately. Have the reason identified at the

nearest repair centre.

 Do not clean the plastic parts with solvents

Solvents, such as petrol, thinners, engine oil or other

substances containing alcohol, may damage the plastic parts

of the machine. Therefore do not clean those parts with such

substances but use soap suds or other – suitable liquids

instead.

 Use original spare parts only

When using spare parts of other manufacturers claim arising

from the guarantee expires and compressor working failures

may occur. Original spare parts are available at authorised

dealers.

 Do not make any alterations to the compressor

Do not make any alterations to the compressor. If the

compressor needs to be repaired please contact the

customer service centre. Any non-approved alteration may

negatively influence the compressor output; it may also

cause serious injuries if made by persons without necessary

technical skills.

 Do not touch any hot compressor parts

Do not touch any cables, engine or other constructional

elements of the compressor in order not to get burnt.

Never keep the device switched on unattended, it could

become source of danger.

 If you execute repairs or service of safety or protective

devices of the machine these parts must be immediately

reassembled after works are finished.



It is necessary to know both re

gulations for preven

tion of

injuries valid at the place of device using and generally

accepted safety rules.

 Safety device functioning needs to be checked before using

the device. Make sure functioning of parts with seemingly

slight damage is really all right.

 Unless otherwise provided in these operating instructions,

the damaged parts and safety devices need to be repaired

or replaced in an authorised service centre.

 Have the damaged switches replaced in an authorised

service centre.

 This device corresponds to all appropriate safety regulations.

Repairs may only be executed by qualified electricians in

authorised service repair centres while using original spare

parts. Failing to observe this regulation may lead to an

accident.

Gude 300-10-50 DG 14 TLG 71126 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info