Bedienungsanleitung Gude 300-10-50 DG 14 TLG 71126 (Seite 13 von 51) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

621510

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

Behaving in Case of Emergency

Provide first aid corresponding to seriousness of injuries

and seek qualified medical advice as soon as possible.

Put the injured person to peace and protect him/her

against other injuries.

Device Use as Designed

For blowing and works with compressed air, in clay-

modelling, for airbrush painting of walls, airbrush

varnishing works, tyre pressure rating, etc.

Residual Dangers

Direct electric contact

A faulty cable or faulty connector plug may lead to a

fatal accident caused by electric current.

Have always the faulty cables and connector plugs

replaced at a specialist. Use the device at a connector

equipped with current protector (RCD) only.

Indirect electric contact

Injury by parts of the machine that are live or by

faulty constructional elements of the machine.

Always pull the connector plug out of socket at

maintenance works. Operate with current protector only.

Insufficient local lighting

Insufficient lighting represents a high safety risk.

Always ensure sufficient lighting at work with this device.

Disposal

Instructions for disposal result from icons on the device,

or more precisely, on the package. Description of each

meaning can be found in the “Marking“ chapter.

Operating Staff Requirements

The operating staff must thoroughly read the operating

instructions before using the machine.

Qualification

No additional qualification is needed for using the device

apart from detailed training by a person with expert

knowledge.

Minimum Age

The device may only be operated by persons that have

reached 16 years of age.

An exception includes device use by juveniles within job

preparation for purpose of reaching skills under

instructor's supervision.

Training

Appropriate training is only needed for device use. No

special training is necessary.

Transportation and Storage

 If the device is stored for a longer period of time it

needs to be thoroughly cleaned and stored so that it

was not accessible to unauthorised persons.

 The compressor must never be stored or transported

laying or under pressure!

 Pressure in the air jet may be reduced at

compressed air cooling.

Assembly / First Putting into Operation

If the compressor is supplied without wheels assemble it with a

screw wrench according to pic. 2. The sequence of screws, nuts

and washers is evident from pic. 2. In case of need, a rubber foot

also needs to be screwed on. Jointing materials, such as screws,

nuts, etc. are included in the supply.

Transport stopper of the oil tank needs to be

exchanged for throat for oil adding and correct oil level

needs to be ensured (see the "Handling Throat for Oil

Adding and Oil Level Inspection" chapter) before putting the

compressor into operation)

Check the oil level at every startup!!!

Handling

Pull the connector plug out of socket before each

maintenance, arrangement and adjustment of the

compressor.

Working Pressure Adjustment

 The working pressure may be adjusted very easily: By

turning the knob (2) in the + direction the working

pressure increases. By turning the knob in the – direction

the working pressure reduces. The working pressure

may be locked by tightening the snap ring.

 The compressor is equipped with an automatic safety

valve releasing pressure at overpressure. You may

release pressure from the air jet manually by pulling

the valve ring (10).

ATTENTION:

Realise the amount of compressed air you will need from the

device! The pressure itself, however, is NOT decisive for perfect

and sufficient operation. Short switching the compressor on after

a long break without use is common!

Have any repairs executed exclusively at qualified specialists.

Turn the compressor never about the power,

otherwise no discharge of the unit is done. Without

discharge, the electric motor through the back pressure

damage!

Throat for Oil Adding and Oil Level Inspection

Transport stopper needs to be exchanged for throat

for oil adding and correct oil level needs to be ensured

before putting the compressor into operation.

Check the oil level at every startup!!!

Oil change

Since arriving on the piston can chip, it is absolutely

necessary after the first 10 hours of operation to carry out an

oil change. We recommend that you are our compressor

(SKU: 40056). Later, depending on the operation of the

compressor, all 100 to 200 hours of operation an oil change

place. In order to carry out oil changes, open the drain screw

(16) and begin the process of waste oil in a suitable

container.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude 300-10-50 DG 14 TLG 71126 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info