Bedienungsanleitung Gude BIG WHEELER 560 Mega B S 95125 (Seite 36 von 49) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

626212

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

3. Mulching

When the mulching wedge is inserted (see the picture

and “Changeover to mulching“ article) the grass is not

thrown up but ground by the cutting knives and the

grass will remain as surface fertilisation on the lawn

Changeover to mulching

1. Assembly and disassembly of accessories must always

take place when the engine is switched off.

2. Remove the grass catcher, insert the mulching wedge to

the ejection channel and lock the mulching wedge (1) point it

against two outlets (2) in the bottom part and ensure it with a

self-securing hook (3).

3. Please make sure the mulching wedge is mounted firmly

after the changeover.

4. Attention!!! Use original equipment from the producer

only.

5. Disassembly

Press with thumb in the middle (3) then release and deflect

the mulching wedge downwards.

Attention!!!

If the mower is blocked during mulching reduce the

travelling speed so that the knife could continue in

grinding the grass and spread it on the lawn. Never

remove the gathered grass with your hands.

DRIVE CONTROL

The self-propelling travel is controlled as follows: Press the

operation lever (lever for automatic stopping) (12) towards the

handle and simultaneously press the drive lever towards the

handle (13).

The forward movement is stopped by releasing the drive lever

(13).

CUTTING HEIGHT ADJUSTMENT

Depending on the cutting height required it is necessary to

adjust the height of wheels. Adjust the height with the lever (8)

as you wish. The middle position is most suitable at most

mowers.

Important tips and advice for grass cutting!!!

• Under certain conditions, e.g. when the grass is very high, it

may be necessary to adjust bigger cutting height so that effort

at pushing the mower was reduced, engine overloading

removed and blocking of grass in the mower prevented. It is

possible you will also have to reduce the mower travel speed

and/or cut the area again.

• If cutting is very difficult it may be suitable to reduce the travel

speed and mower gear.

• Vent ports in the grass catcher may get blocked if the catcher

is not cleaned regularly. Clean the grass catcher regularly with

water and let it dry before use.

• Keep the upper part of the engine in the

starter place clean. Air flow will be improved

and engine life increased by doing so.

• Cut in dry weather only.

• Always keep the knives sharp.

MAINTENANCE

IMPORTANT – Regular maintenance is unavoidable for

constant operational reliability and keeping the original

device output.

1) Keep all screws and nuts tightened so that you were sure

the device is in an operation-reliable condition. Regular

maintenance is necessary for safety and trouble-free

operation.

2) Never store the device with fuel in closed rooms as the

evaporating fuel may ignite.

3) It is necessary to let the device cool down and empty fuel

from it before storing in closed rooms.

4) In order to minimise the risk of fire keep the engine

and muffler and the fuel tank clean and with no grass,

leaves and fats. Do not store the grass cut with the

mower.

5) For safety reasons, avoid using a device with a worn

or damaged parts. Replace any faulty parts with new

ones, do not repair them. Use original spare parts and

original spare knives only.

Parts with quality different from the one prescribed

may damage the device and threaten your safety.

6) If it is necessary to empty the fuel tank do it outside and

with cold engine.

7) Wear solid protective gloves at assembly and adjustment

of knives.

8) Check correct direction of rotating and balance of knives

after sharpening.

9) Regularly check wear and pollution of the self-closing

cover and grass catcher.

10) When you must transport the device, carry it in hands or

incline it always wear safety gloves.

Always hold the device at places guaranteeing safe holding.

Take into account the weight of the device and its distribution.

ČLEANING

Clean the device with water, remove the grass and mud from

inside before each use – it will prevent from impurities getting dry

and problems at next starting.

The painting inside the housing may wear down in the course

of time. In order to prevent later corrosion of the device use

anti-corrosive paint for the worn-down spots.

mulching

cutting and

collecting

cuttin

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude BIG WHEELER 560 Mega B S 95125 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info