Bedienungsanleitung Gude BLACKLINE BL 560 E 95305 (Seite 16 von 63) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

626217

Zoom out

Zoom in

Vorherige Seite

1/63

Nächste Seite

WARNING: Alcohol-enriched fuels (gasohol) or fuels with

ethyl alcohol or methanol mixtures may attract humidity and

subsequent acid formation. The clean petrol may as a result

of long storage damage the engine fuel system. If you want

to prevent engine problems you should empty the fuel

system before storing for more than 30 days. Empty the fuel

tank, start the engine and let it run until the fuel system and

carburettor are empty. Add fresh fuel each season. See the

storing instructions, too. Never pour cleaners to the fuel tank

to clean the engine or carburettor. By doing so, you could

cause irreparable engine damage.

ENGINE STARTING

At starting first make sure the spark plug is in its place and

there is sufficient amount of oil and petrol in the device.

CAUTION: The engine may smoke at first starting due

to protective oil film on the inner engine surface.

Consider this as normal.

Engine start with pulley:

1. Primary pump (Fig. 1/14) to be pressed three times!!!

2. Press the automatic switching off lever (12) to

the mobile handle (1).

3. With the automatic switching off lever (12) pulled in

slowly pull out the starting cord (10), when you feel slight

resistance strongly pull in the starter until the engine is

started.

CAUTION: In cold weather or when the machine has not

been used for a longer time it may be necessary to repeat

the first steps for several times.

Engine start with E-Starter:

1. Automatic switching off lever (12) to push button (1).

2. Key to turn and wait until the engine ignites.

ENGINE STOPPING

• If you want to stop the engine release the automatic

switching off lever (12).

WARNING! The knife still rotates for a few seconds after

the engine is switched off. If you want to leave the mower

laying unattended then disconnect the spark plug cap.

Important tips and advice for grass cutting!!!

• Under certain conditions, e.g. when the grass is very high, it

may be necessary to adjust bigger cutting height so that effort

at pushing the mower was reduced, engine overloading

removed and blocking of grass in the mower prevented. It is

possible you will also have to reduce the mower travel speed

and/or cut the area again.

• If cutting is very difficult it may be suitable to reduce the travel

speed and mower gear.

• Vent ports in the grass catcher may get blocked if the catcher

is not cleaned regularly. Clean the grass catcher regularly with

water and let it dry before use.

• Keep the upper part of the engine in the

starter place clean. Air flow will be improved

and engine life increased by doing so.

• Cut in dry weather only.

• Always keep the knives sharp.

MAINTENANCE

IMPORTANT – Regular maintenance is unavoidable for

constant operational reliability and keeping the original

device output.

1) Keep all screws and nuts tightened so that you were sure

the device is in an operation-reliable condition. Regular

maintenance is necessary for safety and trouble-free

operation.

2) Never store the device with fuel in closed rooms as the

evaporating fuel may ignite.

3) It is necessary to let the device cool down and empty fuel

from it before storing in closed rooms.

4) In order to minimise the risk of fire keep the engine

and muffler and the fuel tank clean and with no grass,

leaves and fats. Do not store the grass cut with the

mower.

5) For safety reasons, avoid using a device with a worn

or damaged parts. Replace any faulty parts with new

ones, do not repair them. Use original spare parts and

original spare knives only.

Parts with quality different from the one prescribed

may damage the device and threaten your safety.

6) If it is necessary to empty the fuel tank do it outside and

with cold engine.

7) Wear solid protective gloves at assembly and adjustment

of knives.

8) Check correct direction of rotating and balance of knives

after sharpening.

9) Regularly check wear and pollution of the self-closing

cover and grass catcher.

10) When you must transport the device, carry it in hands or

incline it always wear safety gloves.

Always hold the device at places guaranteeing safe holding.

Take into account the weight of the device and its distribution.

ČLEANING

Clean the device with water, remove the grass and mud from

inside before each use – it will prevent from impurities getting dry

and problems at next starting.

The painting inside the housing may wear down in the course

of time. In order to prevent later corrosion of the device use

anti-corrosive paint for the worn-down spots.

Remove the gearbox cover and clean the space around belt

pulleys and drive belts with a brush or compressed air once or

twice a year.

You should clean the inside of the drive wheels once per

season. Disassemble both wheels. Clean the cog wheels and

their edges off the grass and other impurities with compressed

air or a brush.

KNIFE DISASSEMBLY

For purpose of cleaning / sharpening / replacement

Attention!!! It is necessary to first disconnect the spark plug

before disassembly.

Picture for engine

starting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude BLACKLINE BL 560 E 95305 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info