626566

Gude GF 600 94369 Seite 11

11
Zoom out
Zoom in
Vorherige Seite
1/48
Nächste Seite
Danger from vibrations
Threat Description Protective measure(s)
Whole body
vibrations
Prolonged work with
the machine could
result in bodily harms
due to vibrations.
Make breaks from work
regularly.
Danger from materials and other substances
Threat Description Protective measure(s)
Contact,
aspiration
Inhalation of exhausting
gases could be
extremely harmful for
health.
The machine may be
operated outdoor only.
Fire or
explosion
The machine is driven
with inflammable
mixture of fuel that
could ignite for example
during refuelling.
Do not refuel close to
open flames and do not
smoke during refuelling.
Other risks
Threat Description Protective measure(s)
Objects thrown
away or
splashing
liquids
Stones or soil
thrown away
could cause
injuries.
Make sure that no other
persons are present in the
work area and wear
personal protective means.
Disposal
Instructions for waste disposal implying from pictograms that
are located on the machine or possibly on the packaging. The
explanation of such signs can be found in chapter “Marking
on the machine“.
Requirements for operators
The operator must read the guide for operation carefully
before any use the machine.
Qualification
No special qualification except detailed instruction session led
by an expert is necessary for use of the machine.
Minimum age
The machine may be operated by persons older than 16
years only. The exception is the case of the machine
utilisation by operation by juvenile persons when this occurs
used during profession training to get skills under supervision
of a trainer.
Training
The operation of the machine requires just corresponding
instruction by an expert or the guide for operation. No special
training is necessary.
Technical specifications
Engine design: 4-Takt OHV
Max. output: 3,8 kW/5,1 PS
Swept volume: 139 cm³
Operating width: 380 / 600 mm
Number of plough-: 4 / 6
Noise: L
WA
93 dB
Weight approx.: 34,6 kg
Order No.: 94369
Transport and storage
• The machine may be transported with stopped
engine only.
• Clean the machine thoroughly before storage.
• Store the machine at a clean and dry place.
Fuel or oil could leak out during transport of the
machine. Please secure the machine in a
corresponding way and make preventive protective
precautions to avoid environmental pollution.
Assembly and putting into operation for the first time
(Abb.1-9)
• Impeller (Fig. 1, 6) on the front of the device by means of
nut and screw, (Fig. 2). Thereafter, the spring in the
fender mount (Fig. 3).
• Handle bracket (Fig. 1, 5) with 4 screws behind the
engine mount (Fig. 4 +5)
• The PVC connection between the two handles plug and
tighten the screw on the grip panel.
• Both handles to grip panel screw (Fig. 6)
• Drive lever (Fig. 1, 3) and throttle mount (Fig. 7), the
Bowden cable attached to the drive lever (Fig. 8)
• Depth limiter from the bottom to insert into the hole,
secure with a cut-out with a pin.
Widening:
• Solve cleaver through the bolt from the transmission
drag. Then put the cleaver on the gear shaft and secure
with a bolt.
• Put the cleaver end part on the other cleaver and also
stuck with a bolt to secure.
• Note the correct direction of rotation of the knife! Mount
with 2 screws to extend the fender.
Engine:
• First filling oil into the oil filling (Fig. 13, A) is an up to the
mark (Fig. 14).
• Then, fill petrol in the tank (Fig.13, B).
Safety instructions for putting into operation for the first
time
Always pay attention to tightening of bolting and use
exclusively parts listed in the scope of delivery.
Procedure
Perform the assembly of individual parts in the illustrated
order. Doing so pay attention to proper arrangement of
construction parts according to illustrations.
The machine is delivered without oil and fuel
due to transportation. Fill these according to
the data.
Operation
Rotary wheel in operating position (Fig. 15)
Set the rotary wheel into the position 1 for cultivation. (Fig.
15,1)
ATTENTION!
The machine may be transported only with the rotary wheel in
the position 2. (Fig. 15,2)
The rotary wheel may be adjusted only when the engine is
stopped!
Cutting height calibration (Fig. 16)
Required depth of cultivation is set by shifting the depth
limiter. Three different positions are possible.
… 11 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gude GF 600 94369 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info