Bedienungsanleitung Gude GRK 250-300 LP (Seite 12 von 50) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

624755

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

switch the saw on again before you find and remove the

cause.

 The cut off part should not be restricted in any way. Do

not touch it, do not hold it, do not clamp it and do not

place the end stop against it either. The cut off piece

should be able to move freely along the saw side. If you

prevent the motion in any way, it could get stuck and

thrown away with the rotating disc.

 Avoid any clumsy position of hands when your hands

could slip down or get stuck with the saw disc.

 Pay attention to the disc reaching full speed before

cutting.

 Switch the saw head at a speed so as to avoid any

motor overloading and blocking the disc.

 Before removing any jammed material switch the

machine off, let the disc stop and unplug the machine.

 With the cutting finished, hold the saw head pressed

down, release the switch and wait until the disc stops. It

is only then that you can move your hands.

Emergency Action

Apply the first aid adequate to the injury and get qualified

medical assistance as quickly as possible. Protect the injured

person from more accidents and calm him/her down.

For the sake of eventual accident, in accordance with DIN

13164, a workplace has to be fitted with a first-aid kit. It is

essential to replace any used material in the first-aid kit

immediately after it has been used. If you seek help, state

the following pieces of information:

1. Accident site

2. Accident type

3. Number of injured persons

4. Injury type(s)

Residual risks and protective measures

1. Mechanical residual risks:

 Cut, amputation:

A rotating circular saw blade may lead to serious cutting

injuries. Keep your hands in a safe distance from the circular

saw blade.

 Impact:

If the cut material is held in hand, the rotating circular

saw blade may throw it down and injure you! Secure

the cut material properly using a vice at all times!

2. Exposure to noise:

 Hearing damage:

Hearing may get damaged if the appliance is worked with

for a long time. Personal protective aids to prevent hearing

damage should always be worn.

3. Other risks:

 Thrown-off items or liquids:

Pieces of the cut material secured improperly may be

thrown off and cause injury as a result of circular saw

blade rotation. The cut material should always be secured

and protective glasses worn.

4. Exposure to emission:

 Laser emission:

The appliance is fitted with laser to display the

cutting line. Laser may cause retina damage. Never

look directly to the laser beam.

Disposal

Disposal instructions are given by pictographs on the unit or

packaging. For meaning of individual symbols refer to chapter

“Symbols on Unit”.

Operator Requirements

The operator shall read the instruction manual carefully

before using the unit.

Qualification

No special qualification is required for use of the unit except

for detailed direction by a professional.

Minimum Age

Only persons above 18 years of age are allowed to work with

the unit. Exempted from the provision is the use of the

juvenile trainees if they work in the course of their

professional training with an aim to obtain the skill under a

trainer supervision.

Training

Use of the unit requires adequate lesson by a professional or

the use of the manual only. Special training is not required.

Technical Data

Voltage/Frequency: 230 V~50 Hz

Motor Capacity: 1900 W

Saw disc - Ø: 250 x 20

Saw disc speed: 5000 rpm.

Cutting width at 90°(max): 70 x 310 mm

Cutting width at 45° (max): 40 x 210 mm

Noise level L

: 107 dB

Weight including support: 20 kg

Weight without support: 18 kg

Transport and storage

If the appliance has not been used for a long time, unplug it

and keep it in a place inaccessible to children.

Make sure such place is dry and safe.

Cable Cross-section

Cable length Required Cross-section:

to 15 m 1,5 mm²

15 – 40 m 2,5 mm²

If the supply cables are too long while the cross-section of

them is small, the voltage drops, which may cause the motor

difficulties. Therefore, a supply cable of sufficient cross-

section is required for the saw to work perfectly. The cables

length show in the table applies to the distance between the

switchboard/fuse box and the trimming saw plug. It is of no

relevance then whether a supply and an extension cables are

combine or it is a supply cable alone.

Glossary of Terms

 Saw Shaft

the shaft, which the saw disc is attached to.

 Cross cut

Cutting across the grain.

 Skew Cut

Cutting not at right angle to the cut piece surface

 Bevel Square Cut

Cutting not at right angle to the cut piece front edge

 Double Bevel Square Cut

bevel and skew cut combination

 Revolutions per minute

Revolutions done by a rotating object per one minute .

 Cutting line

Line on a piece to be cut off on the saw table directly

aligned with the saw disc, which applies also to the part

already cut away.

 Spring Set

Dimension, by which the saw tooth tip is kicked up away

outside the saw disc body width.

 Saw Kerfs

A kerf formed by the rotating saw disc in the material cut.

 Improper Angular Adjustment

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude GRK 250-300 LP Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info