Bedienungsanleitung Gude GS4000 94621 (Seite 11 von 64) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

628258

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

rubber, H07RNF type, according to DIN 57282 or DIN

57245 standards.

Never touch, lift or carry with a cable a pump

connected to network (pic. E)

It is necessary to make sure the connecting socket was not

near water and humidity and the plug was protected against

humidity.

Before putting the pump into operation, check whether the

electric cable and/or socket are not damaged.

Before any work on the pump, pull the plug out of the

socket.

Instructions step by step

• Connect the water hose to appropriate pump outlet (see

the Assembly and first putting into operation).

• Fix the rope, chain, etc. to the pump handle and place it

to the right place.

• Put the pump “sideways“ (pic. D) to the pumped

medium. Make sure the floating switch is in the operating

position.

• Plug in the pump.

• Rinse the pump with clean water after work finishing.

Floating switch positions (pic. B + C)

The operating or shutdown point of the pump can be set

with various floating switch positions. In pic. B you can see

the float cable without any fixation change with full switch

radius. The figure 1 is the working position and figure 0 the

shutdown position.

Due to appropriate fixation of the float cable, possible on the

pump handle, the switch radius can be reduced when there

is no sufficient space or at a corresponding level control.

The figure 1 in pic. C is the working position and figure 0

the shutdown position.

Failures – causes - removal

(problem): Engine does not start

(cause):

1. No system voltage

2. Blocked pump wheel

3. Floating switch in shutdown position

(measures):

1. Check the voltage

2. Inspect the pump wheel for foreign

objects

3. Check the water level (pic. B/C)

(problem): Pump does not suck

(cause):

1. Pump without water

2. Water level too low

3. Blocked pump wheel

(measures):

1. Let the air bubbles release (pic. D)

2. Switch the pump off, water level

must go up.

3. Remove the obstruction

(problem): Insufficient amount of water pumped

(cause):

1. Dirty tube filter

2. Water level quickly going down

3. Maximum head of delivery exceeded

4. Transport guide broken

(measures):

1. Clean the tube filter

2. Ensure sufficient inflow

3. Check the transport path length

4. Check the transport guide

(problem): Thermal detector switching the pump

off

(cause):

1. Dirty tube filter

2. Water temperature too high

3. Pump running continuously at

maximum pressure.

(measures):

1. Clean the tube filter and let the

pump cool down

2. Reduce the water temperature

3. Make more breaks

Inspections and maintenance

Except for the below-described cases, the pump must be

delivered to the customer service department for any repairs.

Sand and other abrasive solids cause premature wear and

pump power reduction. Works on the pump electric

equipment can explicitly be executed by the customer service

department only (that also applies for the electric cable and

float). The drowned sludge pumps are virtually maintenance-

free. Oilless bearings. Occasional filter support cleaning is

enough, no other maintenance is necessary. Original spare

parts must only be used in any case.

To ensure long service life of the pump seal, we

recommend rinsing the pump with clean water in regular

intervals.

Safety instructions for inspections and maintenance

It is always necessary to interrupt feeding (plug pulled out of

socket) and make sure the pump is not going to start before

any pump maintenance. Only a regularly maintained and

treated appliance can serve as a satisfactory aid. Insufficient

maintenance and care can lead to unforeseen accidents and

injuries.

Inspection and maintenance plan

Time interval Description Any other

details

As needed

Cleaning and rinsing

out

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude GS4000 94621 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info