Bedienungsanleitung Gude GSX 1100 (Seite 11 von 37) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

628271

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

rinsed with clean water when used in very dirty water. The

switching on and off heights can differ.

Thermal fuse/engine protection circuit-breaker

The drowned pump is equipped with an engine protection

circuit-breaker. If the engine is overheated, the engine

protection circuit-breaker will automatically switch the pump

off. Cooling time is app. 25 minutes, the pump subsequently

switches on. If the engine protection circuit-breaker switches

on, it is absolutely necessary to identify the cause and

remove it (see also the “Failure searching“). The given data

cannot be used for “family style“ repairs as it requires

specific professional knowledge. You must contact the

customer service department at any failures.

Instructions step by step

• Connect the water hose to appropriate pump outlet (see

the Assembly and first putting into operation).

• Fix the rope, chain, etc. to the pump handle and place it

to the right place.

• Put the pump “sideways“ (pic. D) to the pumped

medium. Make sure the floating switch is in the operating

position.

• Plug in the pump.

• Rinse the pump with clean water after work finishing.

Operation

The pump is put into operation when the plug is inserted in

appropriate socket and the floating switch is in the required

position (see the Instructions). If the pump is lifted or

transported, it is done with an assembled handle and not with

the connecting cable. If the pump is being plunged, a rope,

chain, etc. fastened to the handle need to be used if

necessary.

At muddy, sandy or siliceous soil the pump must be hung on

a rope or chain or put on a suitable wide baseplate to be able

to work plunged. Sand and other abrasive solids reduce the

service life of hydraulic parts and seal of the pump and

therefore they need to be prevented. In frost conditions, the

pump must be removed from the pumped liquid. It is

necessary to absolutely make sure the pump is not exposed

to a risk of frost. The pump must be emptied and stored at a

place protected against frost.

Floating switch positions (pic. B + C)

The operating or shutdown point of the pump can be set

with various floating switch positions. In pic. B you can see

the float cable without any fixation change with full switch

radius. The figure 1 is the working position and figure 0 the

shutdown position.

Due to appropriate fixation of the float cable, possible on the

pump handle, the switch radius can be reduced when there is

no sufficient space or at a corresponding level control. The

figure 1 in pic. C is the working position and figure 0 the

shutdown position.

Continuous operation: The floater can be hung to the side

of the pump; in this position (the floater cable points

downward), the pump runs constantly.

Important: In case of continuous operation, under no

circumstances allow the operation of the pump without

fill!

Important: If the pump is to stay out of service for a longer period of time, make sure by all means necessary that both the

pipelines and the pump itself are emptied. Protect the device against frost. The pump can only be stored entirely empty.

Failures – causes - removal

Failures Causes Removal

Engine does not start

No system voltage

Blocked pump wheel

Floating switch in shutdown position

Check the voltage

Inspect the pump wheel for foreign objects

Check the water level (pic. B/C)

Pump does not suck

Pump without water

Water level too low

Blocked pump wheel

Let the air bubbles release (pic. D)

Switch the pump off, water level must go up.

Remove the obstruction

Insufficient amount of

water pumped

Dirty tube filter

Water level quickly going down

Maximum head of delivery exceeded

Transport guide broken

Clean the tube filter

Ensure sufficient inflow

Check the transport path length

Check the transport guide

Thermal detector

switching the pump off

Dirty tube filter

Water temperature too high

Pump running continuously at maximum pressure.

Clean the tube filter and let the pump cool down

Reduce the water temperature

Make more breaks

Inspections and maintenance

Be sent with the exception of cases described below, the pump for repairs required for service.

Safety instructions for inspections and maintenance

It is always necessary to interrupt feeding (plug pulled out of socket) and make sure the pump is not going to start before any pump

maintenance.

Only a regularly maintained and treated appliance can serve as a satisfactory aid. Insufficient maintenance and care can lead to

unforeseen accidents and injuries.

Inspection and maintenance plan

Time interval Description Any other details

As needed Cleaning and rinsing out Function check of the floating switch (C/D)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude GSX 1100 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info