Bedienungsanleitung Gude GWS 450 ECO (Seite 10 von 37) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

623617

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

Training

Use of the unit requires adequate lesson by a professional or

the use of the manual only. Special training is not required.

Technical Data

GWS 450 ECO

Power connection 230 V/50 Hz

Motor output 2,1 kW/P1 (S6/40%)

Speed 2800 U/min.

Ø saw disc 450 x 30 mm

Maximum section 160 mm

Approximate maximum section at

double cutting 200 mm

Cradle width 200 mm

Cradle extension 0-500 mm

Acoustic output level (idling)

measured

guaranteed

96 dB (A)

98 dB (A)

Approximate weight 65 kg

Ordering No. 01837

Transportation and Storage

For a prolonged shutdown, the saw disc and the cradle spring

are recommended to be wiped with an oil-soaked cloth to

protect them from corrosion. Cover the saw with a tarpaulin if

it stands outdoors or at unprotected places. The motor and

the switch should be primarily protected against water.

Residual Hazards and Protective Action

1. Electrical Residual Hazards:

 Direct electrical contact:

Defective cable or plug may cause an

electrical shock Wounds cause by conductive

parts on open electrical or defective structural

parts.

Have the defective cable/plug exchanged by a

professional. Use the unit only if connected via a

faulty current switch (FI).

 Indirect electrical Contact:

Always unplug before any maintenance.

Operate only with FI switch installed.

2. Mechanical Residual Hazards:

 Cutting, incision:

A contact with the rotating saw disc may cause

severe injuries.

Risk of injury by rotating parts

Always be very careful with small pieces to be

worked. Use aids (such as sliding tool or a guide

block/bar). Never touch the disc if it is still moving.

The worn or damaged aid should be replaced

immediately.

 Catching, winding:

Loose garments or jewels may be caught by

moving parts. Always wear tight-fitting clothes

and do not wear jewels that could be caught.

3. Noise Hazards:

 Impaired Hearing:

Prolonged work with the saw may result in

hearing impairment

Always wear ear protectors

4. Materials and Other Substances Hazards:

 Contact, aspiration:

Lungs may be affected by great amount of

dust being formed. Health-hazardous sawdust

emissions from operations without extracting

the dust.

Always wear breathing mask when working with

the unit. Install and use an exhaust equipment.

5. Human Factors Neglect:

 Negligent use of personal protection

equipment:

Operating the unit without adequate PPE may

cause severe external/internal injuries

Always wear prescribed protective clothing and work

considerately.

 Inadequate local lighting:

Insufficient light is a heavy safety risk.

Provide for sufficient lighting

6. Other Hazards:

 Thrown away articles and splashes:

The band or mechanical particles may wound

your eyes in the course of cutting job.

Always wear protection goggles.

Assembly and Initial Operation (Fig. 2, 3, 4, 5 + 6)

Fig. 2 + 3 Install the connector

Fig. 4 + 5 + 6 Blade mount

Saw Disc Replacement on GWS Models (Fig. 4, 5 + 6)

Saw disc replacement on GWS models:

1. Disconnect the power supply.

2. Remove the cotter pin at the end of the cradle setting

rod (Fig. 4), put up the rod and tip the cradle forward

(Fig. 5 ).

3. Lock the disc on the sawdust tank with a screw.

4. Always wear safety gloves at these operations.

5. Release the setting screw using a C-wrench with

caution. The cautiousness is essential as unexpected

lapse of the wrench may result in a severe injury of the

hand!

6. Carefully remove the saw-blade in the upward direction

and put a new blade in the installation procedure is

reverse.

7. When changing or carrying the saw-blade, always hold it

safely and firmly. The disc is heavy at it may be slipping

down. If it falls out of your hands, it may cause severe

injuries. .

8. After the disc replacement, set the cradle so that the disc

distance is 50 mm (Fig. 6).

Caution: Remove the lock screw again!

Caution: Always wear safety gloves when replacing

the disc to avoid accidents.

Initial Operation Safety Instructions

 Before putting the machine in operation, check to see

that the machine is connected to the mains, it does not

show any damage and the screwed joints are tight.

 Re-check that the power supplying cable does not show

any apparent damage, such as cracks or scraped spots

 Check to see that no foreign objects got in the machine

that could be shot out on switching.

 Always stand off the direction of shooting out the

objects that were caught by the saw-blade (chips,

pieces of bark).).

 It is prohibited to operate the machine being under

influence of narcotics and similar agents such

 As alcohol.

 Do not use the machine for performing any other works

than those it has been designed for as indicated in this

instruction manual “Working Instructions”

 Under any conditions observe our instructions of safety

and accident prevention, putting operation, function,

work and care and maintenance. Variances are possible

upon our written consent only

 Never leave the machine without having disconnected

the power supply (unplugging the machine) and having

the machine secured against use by unauthorised

persons.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude GWS 450 ECO Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info