Bedienungsanleitung Gude GWS 450 ECO (Seite 11 von 37) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

623617

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

 The connection to the source should have an under

voltage protection)!

 Use the supply cable as short as practicable or have

the diameter if it as large as possible. Use of a long

thin cable results in heating the motor up and the

damage entailed may be non-repairable.

Warning: Extension cable diameter 1,5 mm² and 2,5

mm² from the length of 20 m and more!

Never switch the machine on when braking is in

progress. Observe the switching interval of 1

minute as a minimum

The saw should not be operated unless the switch

braking function is guaranteed.

Operator Safety Instructions

 Before switching the unit on, all the safety and protection

devices have to be fitted at correct places.

 Never cut pieces of wood so small that they cannot be

held safely.

 Before getting down to cutting, take care to see that the

saw-blade is installed in the correct direction of rotation.

The teeth should be in the direction of arrow on the

operator’s side. See also the chapter “Putting in

Operation”.

 Use only the saw-blades that are sharp as appropriate

and the pitch of teeth on which is sufficient.

 You will save the energy and the motor of your saw. Any

damaged and deformed saw discs should be eliminated

and discarded to prevent untended use of them. The

circular saw will apply braked on the disc within

approximately 15 seconds after switching off. (Whirring

of the motor for several seconds after the stop

is normal). The disc should turn freely

 If working wood treated or processed in any way before,

special attention should be paid to nails, screws etc.

Before getting down to work, remove any foreign

objects.

 Before switching the main switch on, make sure the saw

disc is fitted correctly and all the unit moving parts are

free.

 Warning! If in doubt at the assembly of this circular

bench saw, consult an expert at an authorised servicing

centre.

Preparation of Job

Never overload the unit. Base your work on the

maximum cutting capacity of the unit. Make sure that the

machine will not tip over due to jam of a piece of wood.

 Do not use the unit until you have read the

instruction manual carefully.

 Observe all the safety instructions shown in the

manual.

 Be responsible to the others.

Only one person is allowed to use the saw in principal.

Operation (Fig. 7)

 Put the wood in the cradle as safely as possible (no

wobbling) .

 Carefully mind any foreign articles and Chipped off

place.

 Take the cradle by both hands holding the handle,

support it with your thigh and push it slowly and evenly in

the saw disc.

Step by Step Instructions

In the course of cutting, the right hand conducts the

cradle towards the disc, holding it by handle. The right

hand may get easier by pressing the thigh against the

cradle.

Pressing against the cradle, the disc cover will release

and after completion of the cut, it will get back in the

starting position (the disc is covered up) owing to the

spring tension.

Inspections and Maintenance Safety Instructions

Only a unit that is maintained and cared for regularly may be

a satisfactory aid. Insufficient maintenance and care may

result in unforeseen accidents and injuries.

Inspections and Maintenance

Always keep the swing saw clean. It will be sufficient to clean

the saw from saw dust after the job is done using a brush or a

cloth with the saw disc stopped and the power supply

disconnected. The saw dust and dust on motor cooling ribs

may cause the motor overheating. -> Clean the cooling ribs at

regular intervals.

Inspections and Maintenance Schedule

Time Interval Description

After every use

 Remove sawdust, dust and dirt from the

saw – clean.

As necessary

 Sharpen the disc, replace it if necessary.

Troubles-Causes-Troubleshooting

Trouble Cause Troubleshooting

Motor will not run

1. No power supply to the unit.

2. Thermal sensor has interrupted power

supply.

1. Check the supply and power line, invite an expert

electrician to consult.

2. Wait for 5-10 min and switch on again.

Motor will not slow down

1. Mechanical motor brake is worn 1. Have a new brake mounted in a servicing centre.

Motor will shut off in the

course of work.

1. Thermal sensor defective

2. Motor circuit breaker

switches off for overloading.

1. Have the replacement done by an expert

electrician only.

2. Wait for the motor to cool down and restart in 5-10

min.

Reasons of overloading

1. Supply line is too long or its cross section is

too small.

2. The saw disc is not sharp as needed.

3. The chamfer of the saw disc teeth is not

correct.

1. The extension cable has to be dimensioned

appropriately, 1.5 mm

2. Sharpen the saw disc.

3. Have the teeth chamfered by an expert.

Scorch traces on the

piece being worked

1. Blunt saw disc. 1. Sharpen or replace the saw disc.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude GWS 450 ECO Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info