Bedienungsanleitung Gude HKS 1200 58045 (Seite 13 von 48) (Deutsch, Englisch)

624908

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

- Avoid abnormal body posture.

Assume a safe posture and keep constant balance.

- Treat your tool with care.

Keep the tool sharp and clean so that it is possible to work with it better and safer. Follow the maintenance regulations and

appliance replacement instructions. Check regularly the cable of your electric tool and have it replaced by an authorised

professional if damaged. Check regularly the extension cables and replace them if damaged. Keep the handles dry and

with no oil and fat.

- Pull the plug out of socket.

If you do not use the electric tool or before maintenance and at replacement of e.g. circular saw blades, drills, etc.

- Do not leave any adjusting instruments in the appliance.

Before switching the appliance on, check whether you have removed all wrenches and adjusting instruments.

- Prevent starting with no attendance.

Do not carry the electric tool plugged in with your thumb on the switch. Make sure the switch is off when plugging into the

socket.

- Extension cables in open air.

In open air, use only extension cables approved and adequately marked for that purpose.

- Be careful.

Pay attention to what you are doing. Work reasonably. Do not use the electric tool when not concentrated.

- Check the electric tool for any damage.

Before using the electric tool again, you need to carefully check the perfect and specified working of the guard devices or

slightly damaged parts. Check whether the rotating parts work faultlessly and do not drag behind or whether any parts are

not damaged. All parts must be installed properly and satisfy all conditions to ensure faultless operation of your electric

tool. Any guard devices and parts that are damaged must be duly repaired or replaced by an authorised specialised shop

unless provided otherwise in the Operating Instructions. Have any damaged switches replaced by a customer service

shop. Do not use electric tools at which the switch cannot be turned on and off.

CAUTION

- Use only accessories or extensions specified in the Operating Instructions. Using any other extensions and accessories

can represent a risk of injury.

- This saw corresponds to appropriate safety provisions. Repairs can only be executed by a professional electrician and only

original spare parts must be used, failing which there might be injuries of the operator.

Safety instructions specific for this appliance

Do not touch the cutting area and circular saw blade with your hands. Hold the auxiliary handle or engine case by the

other hand. If both hands hold the saw, the circular saw blade cannot injure them.

Do not touch under the workpiece. The protection cover is unable to protect you against the circular saw blade under the

workpiece.

Adjust the cutting depth to the workpiece thickness. Less than one full tooth height must be seen under the workpiece.

Never hold the cut workpiece in your hand or above the leg. Secure the workpiece in stable fixture. It is important that the

workpiece is fixed well so as to minimise the risk of body contact, circular saw blade jamming or loss of control.

Grab the saw only on insulated working surfaces if you carry out works at which the extension or proper feeder cable

can become conductive. Metal parts of the saw also become conductive by getting in touch with the conductive line, which

leads to electric shock.

Always use a stop or straight edge guiding for longitudinal cutting. This improves the cut accuracy and reduces the

possibility of circular saw blade getting jammed.

Always use circular saw blades with correct size and an appropriate hole for clamping (e.g. star or round). Circular saw

blades not appropriate for assembly parts of the saw experience radial run-out and lead to loss of control.

Never use any damaged or poor washers or screws of the circular saw blade. Washers and screws of the circular saw

blade have been designed specially for your saw, optimum performance and operational safety.

Causes of backlash and protection against it:

Backlash is a sudden response as a result of seized, jammed or poorly balanced circular saw blade that causes the saw to go

up uncontrolled and then moves off the workpiece towards the operator.

When the circular saw blade gets seized or jammed in a closed cutting gap, the engine power hits the saw back towards the

operator.

If the circular saw blade is revolved or poorly balanced in the saw cut, teeth of the back edge of the circular saw blade might get

jammed in the workpiece surface, which results in the circular saw blade going up from the cutting gap and saw bouncing back

towards the operator. The backlash is a result of wrong or faulty use of the saw. It can be prevented by the appropriate safety

measures described below.

Hold the saw firmly with both hands, placing them to a position in which you are able to absorb the backlash force. Always stand

from the side of the circular saw blade; never put the circular saw blade to the same level with your body. With backlash, the

saw might bounce back but the operator can cope with the backlash force by appropriate safety measures.

If the circular saw blade gets jammed or you interrupt the work then switch the saw off and hold it easily in the workpiece until

the circular saw blades stops. Never try to take the saw away from the workpiece or pull it back if the circular saw blade is

turning, failing which you will face a risk of backlash. Find out and remove the cause of the circular saw blade getting jammed.

Gude HKS 1200 58045 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info