Bedienungsanleitung Gude IND. 25 E 85100 (Seite 7 von 102) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

628922

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

CONTENTS

IDENTIFICATION OF PART “DI” 7

SAFETY INFORMATION 7

STARTING THE HEATER 7

TURNING OFF THE HEATER 8

SAFETY DEVICES 8

MOVING AND TRANSPORTING THE HEATER 8

PREVENTATIVE MAINTENANCE PROGRAMME 8

HEATER FUNCTIONING DIAGRAM 9

ELECTRIC CONTROL PANEL 9

TROUBLESHOOTING 10

IDENTIFICATION OF PART “DI”

Series DI is a line of hot air generators with indirect heating

system. These generators have a heat exchanger that enables

to separate exhaust combustion gases from the heat released in

the environment, so that it is possible to inject a ﬂ ow of clean hot

air in the area that needs to be heated and to discharge exhaust

fumes externally.

Serie DI hot air generators is designed in compliance with

current safety, performance and life standards, is ﬁ tted with

safety devices conﬁ gured to guarantee continuous operation,

minimize noise and are manufactured in carefully selected

materials that ensure maximum reliability.

SAFETY INFORMATION

WARNING

IMPORTANT: Read the manual carefully before attemp-

ting to assemble,switch on or service this heater. The use

of the heater may cause serious or fatal injuries resulting

from burns, ﬁ re, explosion, electrical discharge or carbon

monoxide poisoning.

DANGER:Carbon monoxide poisoning can be fatal!

Carbon monoxide poisoning The ﬁ rst symptoms of carbon

monoxide poisoning are similar to those of ﬂ u, with headache,

dizziness and/or nausea.These symptoms may be caused by

the defective functioning of the heater. Go outside into the open

air immediately! Have the heater repaired. Some people feel

the effects of carbon monoxide to a greater extent, especially

pregnant women, those suffering from anaemia, cardiac or lung

conditions, those who are drunk and anyone at a high altitude.

Ensure that you have read and understood all the warnings.

Keep this manual for future reference – it is a guide to the safe

and correct functioning of the heater.

• Use only fuel oil no.1 in order to avoid the risk of ﬁ re or explo-

sion. Never use petrol, naphtha, paint solvents, alcohol or other

highly inﬂ ammable combustibles.

• Fuelling

a) The individual responsible for fuelling the heater must have

the relevant competence and be completely familiar with the

manufacturer’s instructions and with current norms concer-

ning the safe fuelling of the heaters.

b) Only use the type of fuel expressly speciﬁ ed on the identiﬁ ca-

tion label of the heater.

c) Before adding fuel, extinguish all ﬂ ames, including the pilot

light, and wait until the heater has cooled down.

d) While adding fuel, inspect all the fuel lines and joins to make

sure there are no leaks.

Any leak whatsoever must be repaired before switching on

the heater.

e) In no circumstances must more than one day’s supply of

fuel be stored in the same building in proximity to the heater.

Fuel storage tanks must be kept in a separate location.

f) All fuel tanks must be kept at a minimum distance from hea-

ters, oxyacetylene torches, welding equipment etc. (with the

exception of the fuel tank incorporated into the heater) fol-

lowing regulations.

g) Wherever possible, fuel should be stored in a place where

the ﬂ oor does not allow fuel to seep through and drip onto live

ﬂ ames beneath, which might cause ﬁ re.

h) Fuel must be stored in compliance with current norms.

• Never use the heater anywhere where petrol, paint solvents or

other highly inﬂ ammable vapours are present.

• While using the heater, follow all local ordinances and current

norms.

• Heaters used in the proximity of tarpaulins, cur-

tains or other covering materials must be si-

tuated at a safe distance following regulations.

It is also recommended to use ﬁ reproof materials.

These materials should be ﬁ xed safely so as to ensure that

they do not catch ﬁ re and are not blown by the wind.

• Only use in locations where there are no inﬂ ammable fumes or

high concentrations of dust.

• Power the heater only with electric power that has the voltage,

frequency and number of phases speciﬁ ed on the identiﬁ cation

label.

• Only use earthed three-wire extension cords.

• In order to avoid the risk of ﬁ re, make sure the heater is on a

ﬁ rm, ﬂ at surface when it is being used or is hot.

• When moving or storing the heater, keep it level to avoid fuel

loss.

• Keep children and animals away from the heater.

• Disconnect the heater from the mains supply when not in use.

• When controlled by a thermostat, the heater may come on at

any moment.

• Never use the heater in frequently used rooms or in be-

drooms.

• Never obstruct the air intake (rear end) or the air output (front

end) of the heater.

• When the heater is hot, connected to the mains supply or in

use, it must never be moved, handled, ﬁ lled up with fuel or

serviced in any way.

STARTING THE HEATER

Before turning on the heater and therefore before attaching it

to the mains power supply, check that the characteristics of the

mains power supply are the same as those indicated on the

identiﬁ cation label.

WARNING:The electric power cable of the heater must

be earthed and must have a differential magnetothermal

switch.The electric plug must be connected to a socket

which has a disconnecting switch.

To turn on the machine, do the following:

• Flip switch 1 (Fig. 2) to the position with the symbol: ON – the

fan comes on and after several seconds the heater starts bur-

ning.

The ﬁ rst time the heater is used, or after the fuel circuit has been

completely drained, the ﬂ ow of fuel oil to the nozzle may be in-

HOT AIR GENERATOR

Gude IND. 25 E 85100 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info