Bedienungsanleitung Gude IND. 25 E 85100 (Seite 8 von 102) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

628922

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

sufﬁ cient and may activate the ﬂ ame cut out mechanism, which

will turn off the heater;if this happens, wait for about a minute

and then press the reset button 1 (Fig. 2) to start the machine

again.

The ﬁ rst steps to take if the machine does not work are the

following:

1. Check that there is fuel in the tank.

2. Press the reset button 2 (Fig.2) ON.

3. If the heater still does not work, consult the

“TROUBLESHOOTING”guide.

TURNING OFF THE HEATER

To turn off the machine, move switch 1 (Fig. 2) to the “0” position

The ﬂ ame will go off and the fan will continue to function until the

combustion chamber has cooled down completely.

SAFETY DEVICES

The heater is equipped with an electronic device to control the

ﬂ ame.If there is an anomaly in the functioning, the machine will

be turned off and the reset button light 2 (Fig.2) will come on.

An over-heating thermostat cuts in and shuts off the fuel supply

if the heater overheats:the thermostat resets itself automatically

when the temperature in the combustion chamber diminishes

and reaches the maximum permitted value.

Before turning the heater on again, the cause of the overheating

must be identiﬁ ed and removed (for example, a blockage in the

suction oriﬁ ce and/or of the air ﬂ ow duct, the non-functioning

of the fan). To turn on the machine again, press the reset but-

ton and repeat the speciﬁ c instructions outlined in the section

“STARTING THE HEATER”.

MOVING AND TRANSPORTING

THE HEATER

WARNING The following steps must be carried out befo-

re moving the heater: turn the heater off, following the

instructions in the previous section; disconnect the plug

from the power supply and wait for the heater to cool.

Before lifting or moving the heater, make sure that the fuel tank

cap is ﬁ rmly in place.

To move the heater, simply grasp the support handle and wheel

the heater.

PREVENTATIVE MAINTENAN-

CE PROGRAMME

To ensure that the heater continues to work properly, it is neces-

sary to periodically clean the combustion chamber, the burner

and the fan.

WARNING The following steps must be carried out befo-

re servicing the heater: turn the heater off, following the

instructions in the previous section; disconnect the plug

from the power supply and wait for the heater to cool.

Every 50 hours of use it is necessary to:

• Dismantle the ﬁ lter cartridge, remove it and clean it with clean

fuel oil.

• Remove the exterior cylindrical casing and clean the inside

and the blades of the fan.

• Check the condition of the cables and the high voltage connec-

tions on the electrodes.

• Dismantle the burner, clean the parts, then clean the electro-

des and regulate them to the distance indicated on page 95 in

the electrode regulation diagram.

HOT AIR GENERATOR

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude IND. 25 E 85100 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info