Bedienungsanleitung Gude Pro 310-10-50 PRO 75505 (Seite 15 von 67) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

628969

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

Operator requirements

The operator must carefully read the Operating Instructions

before using the appliance.

Qualification

No special qualification is necessary for using the appliance

apart from detailed instruction by an expert.

Minimum age

The appliance can only be operated by persons over 18 years

of age. An exception includes youngsters operating the

appliance within their professional education to achieve

necessary skills under trainer's supervision.

Technical specifications

310/10/50 PRO

Connection: 230 V/50 Hz

Engine power: 2100 W/P1

Air jet capacity: 50 l

Suction power: 295 l per minute

Effective volume delivered: 210 l per minute

Cylinders: 1

Revolutions: 2800 revs per minute

Max. pressure: 10 bar

Weight: 35 kg

Article No. 75505

Transport and storing

The appliances are mobile and can practically be used

everywhere. If the compressor is wall-mounted, the minimum

distance of 30 cm must be kept to ensure appropriate cooling.

Appliances must necessarily be transported in a vertical

position; otherwise, oil will run out of the air hole of the engine

case. Prevent any hits to fittings.

Residual risks and protective measures

Electrical residual risks:

1. Direct electrical contact:

Risk of electric shock

To be used in electrical networks with a safety switch

against stray current (RCD-FI 30 mA) only.

2. Indirect electrical contact:

Risk of electric shock

To be used in electrical networks with a safety switch

against stray current (RCD-FI 30 mA) only.

Thermal residual risks:

1. Burns, chilblains:

Contact with the cylinder head and pressure lines

may cause burns.

Avoid both of these construction elements.

Exposure to noise:

1. Hearing damage:

Long stay in the immediate vicinity of the appliance

may damage hearing.

Wear headphones.

Neglecting the ergonomic principles:

1. Human behaviour / erroneous behaviour:

Compressed air current may lead to serious injuries.

Never hold the current in body holes.

Compressed air may cause tanks and tyres to break.

Do not exceed the max. filling size.

Installation and first start-up

Pic.2+3+4:

1. Remove the oil tank transport protection (if applicable)

pic. 3

2. Insert the attached oil gauge or plug instead.

3. Oil gauges or plugs, pic. 4 (failing to do so will increase

pressure in the engine case and oil will spirt).

Electrical connection; grounded connections to be used

only:

a) 230 V appliances are supplied with plugs fitted with a

ground contact

The following must be considered as far as 230 V

appliances are concerned:

If a too long extension cable with a too small cross-section

is used, voltage will drop, which may result in a more difficult

starting and increased engine load. If possible, we

recommend connecting the engine cable directly to the outlet

and using longer air hoses (another measure: see the winter

operation).

Recommended cable cross-section values for all 230 V

appliances:

Length within app. 10 m = 1.5

Length within app. 20 m = 2.5

Oil level check (for oil compressors only):

Oil may leak when the appliance is transported. Please check

the oil level on the aperture or using an oil gauge (more

information at a similar description with a picture)

Winter operation of compressors

The following must be considered in colder seasons

when operating the compressors: Oil gets thicken and its

viscosity increases with low temperatures in the engine case.

This makes first appliance starting before warm-up more

difficult. Proceed as follows when facing difficulties:

1. Reduce any pressure in the air jet to zero.

2. Open the drainage screw on the bottom part of the air

jet.

3. Unless being absolutely necessary, do not use any

extension cable!

4. Switch on the compressor and let it run (without any

extension cable). With the drainage screw open, let it run

for app. 2-3 minutes to enable air to leak and thus

pressure to reduce. The appliance will warm in these 2-3

minutes to enable further operation.

5. After 2-3 minutes, close the drainage screw. The air jet

can now be filled and pressure increased.

6. Change oil – use 5W40 synthetic oil for light running

or, as alternative, SAE 80 gearbox oil.

7. If the compressor does not start despite all the effort, put

it out of operation for half an hour to one hour in a

tempered room to warm up.

8. Please contact the customer service centre for more

difficulties.

All documents necessary for proper operation are

included in the supply (see the simple regulation for

pressure vessels). When used for industrial purposes,

an inspection is necessary before the appliance is used

for the first time under the operating safety regulation.

Safety instructions for first start-up

Procedure

1. Switching compressors on and off:

The On/Off button (rotary and pull switch) is up on the

pressure switch cover at all compressors. Switch

positions are marked as "0" and "I". When plugging, the

switch must be in the "0" position, then the appliance

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude Pro 310-10-50 PRO 75505 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info