Bedienungsanleitung Gude Pro 310-10-50 PRO 75505 (Seite 16 von 67) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

628969

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

may be started. When switching the appliance off, put

the switch to the "0" position first and then unplug the

compressor. Never switch the appliance off by

unplugging as this would prevent depressurising.

Caution: Empty the condensate at regular intervals

(monthly) (see the drainage screw).

Operation

1. Using pneumatic tools and devices

Please follow the air consumption information of

manufacturers. Check whether the power of your

compressor is enough to operate the given device. The

air consumption table details may be used as

benchmark values.

2. Servicing and maintenance

Check regularly the oil level and add some if necessary.

Clean the air filter if dirty; wash the filter inserts in a

detergent - do not use thinners or solvents. If

necessary, order new inserts from the customer service

centre.

3. Air jet drainage:

Regardless of the type of compressor, the drain valve is

placed on the bottom part of the air jet at all

compressors. Drain only if the air jet is under pressure.

4. Opening the drain valve:

Unscrew the screw closure to such extent the air

deflates. Any accumulated water is blown out with the

air.

5. Rusty water:

Rusty water may run out when the air jet is initially

drained. Rusty water is caused by clips fallen to the

tank when producing air jet and disintegrated

subsequently. This is quite normal and water gets

clearer after several drains.

Oil filler neck and oil level checking (for oil compressors)

At appliances fitted with an oil gauge (1), add oil after

removing the gauge (1) to the appropriate hole (2) and check

the level using the gauge marking. At appliances with an

aperture and marking in the glass, remove the oil filler neck

and add oil up to the aperture marking. If the aperture has no

marking, 2 3

– 3 4

filling of the aperture is appropriate. The

oil drainage screw is always on the side or bottom part of the

engine case.

Air fitting and clack valve

Pic. 8

1. Air fitting (2): Air ducting (2) at all compressors is

connected using a quick-acting coupling. Both reduced

pressure and complete pressure from the air jet may be

drawn.

2. Clack valve: The clack valve is located at the end of the

main air ducting, at the air input to the air jet. The

connection point is different for various types of

compressors.

Ducting goes from this valve to the valve to make starting

easier.

3. Pressure-relief valve: Depending on the compressor

type, it is located on the pressure switch (4), on the

pressure control valve or on the air jet. The pressure-relief

valve responses to any malfunction of the pressure switch

(4) and thus limits the pressure in the air jet to the max.

cut-off pressure + 1 bar!

4. Pressure control valve (1): To set the currently needed

pressure, please press the regulator up and set the

requested pressure + 1 bar on the air gauge. To lock the

pressure control valve (1), press the regulator down

again. If necessary, provide additional regulation after the

first operating cycle in the same way.

Safety instructions for the operator

• Use the appliance only after careful reading and

understanding of the Operating Instructions.

• Please follow all safety instructions specified in the

Operating Instructions.

• Behave responsibly towards other persons.

Inspections and servicing

IMPORTANT: After app. half an hour to

one hour of operation, please check the cylinder head screws

and tighten them if necessary. Torque: max. 10 - 20 Nm/by

hand force. Later: cylinder head screws and all other screwed

connections on should be checked every 200 - 300 operating

hours and tightened if necessary.

Servicing

Clean the filter on the suction side if dirty or replace it. After

operating the appliance for some time, the condensate must

be emptied by opening the drain valve on the air jet. IN case

of continuous operation, this should be done every 4-6 weeks.

If the appliance is used for short works, empty the condensate

once in 3 months

. Belt tension at compressors with a V-belt

must be checked at regular intervals (every 4-6 weeks).

Oil level check and oil change

The appropriate oil level may be checked on the oil aperture

(if applicable) or on the oil gauge.

Maximum level = a small bubble or the upper marking on the

oil gauge must be seen in the aperture.

Minimum level = oil must not get

under the red point in the

middle of the aperture or the lower marking on the oil gauge.

Specified oil = universal oil

- 15 W 40 (100 operating hours)

or Güde 5W40 compressor oil, Art. No. 40056 (300-500

operating hours)

Oil change:

After running in, i.e. after 100 operating hours, oil should be

changed for the first time.

Another oil change after app. 300 - 500 operating hours.

Oil adding: unscrew the filler neck and add oil using a funnel.

Oil drainage: Unscrew the drain screw and let oil run out.

Air filter:

Check the air filter app. once a quarter. Foam filters are

washed with a detergent. Replace the filter if heavily

contaminated with paint or varnish!

Folded filters to be blown by compressed air or replaced if

necessary; not to be washed!

CAUTION:

If more oil is added than the maximum level, spring-energised

seals may get untight. The surplus oil along with the

compressed air will shortly get to the air jet – more oil is thus

consumed - until reaching the common state. If oil does not

reach the minimum level (red point in the aperture or lower

marking on the oil gauge), consequential damages such as

seizure of bearings, connecting rod, piston pin, crankshaft or

piston seizing must be counted with.

CAUTION:

The air hole of the engine case is located in the oil filler neck

(No. 1 or 3).

Air is commonly slightly blown in this place when the

appliance is operated, which is normal. Excess pressure in

the engine case caused by the movement of pistons, which

results in oil leaking in that place is also normal (to be wiped

occasionally).

The claim arising from the warranty will not apply in case

of consequential damages as a result of the failure to

meet the above-mentioned!!!

Gude Pro 310-10-50 PRO 75505 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info