Bedienungsanleitung Gude Pro 310-10-50 PRO 75505 (Seite 18 von 67) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

628969

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

Air consumption of pneumatic appliances / directions for use

Not the electric motor power but the produced air volume (actual power) is decisive for the compressor power. Actual power =

suction power minus app. 35-40% of the power (for each compressors, regardless of the manufacturer). Do not choose too small

compressor power in order not to load it up to the upper limit and to have some reserve for the attached appliances. The air jet size

(capacity in litres) may not be decisive. However, capacity, on the other hand, should not be too small to ensure there is air supply

and the compressor could also cover higher needs in the short term.

If provisions of the generally applicable regulations and these Operating Instructions are not adhered to, the manufacturer cannot be

held liable for any damage.

Action Example of use Directions for use

Necessary

operating

pressure

in bar

Necessary actual

power, air volume

delivered by the

compressor

Blowing Work table cleaning by air,

carburettor cleaning, machine parts

cleaning, cleaning machines off

wooden or metal chips

Short-term use 5 to 11 from 100 I

Spray-painting Water-based paints and thin

varnishes

nozzle 0.5 to 1 mm 3 to 4

Spray-painting

Synthetic resin and nitrocellulose

lacquers, thinned

nozzle 1.2 to 1.5 mm 3 to 5

Spray-painting

Hammer paints and other viscous

lacquers

nozzle min. 2 mm 3 to 5

Minor parts, mudguards

of automobiles, etc. from

120 l.

Entire cars, larger areas

from 280 l.

Spray guns, washing

gun

Cleaners spraying in cold

conditions, oil spraying as

anticorrosion protection, vehicle

bottom protection, insecticides

spraying, etc.

Can be set within the

range of a water jet to

water fog

4 to 7 Depending on the time of

use: 250 l to 400 I

Clipping appliances Wood, cardboard, etc. connecting

using clips within a length of app. 25

Operating pressure

depending on the wood

or material hardness

4 to 7 80 l to 280 I

Nailing appliances Connecting by clips of more 25 mm

and nails within a length of 100 mm

ditto 4 to 7 80 l to 400 l

Pneumatic

superfinishing

appliance

In cars or at bodies As per manufacturer

details

5 to 6 Depending on the time of

use: 300 l to 560 I

Tyre inflation Tyres of car wheels The bigger the

compressor power, the

faster the inflation

Pressure in tyre 120 l to 280 l

Tyre inflation Tyres of trucks or bigger ditto Pressure in tyre 280 l to 560 I

Grease gun All appropriate works As per manufacturer

details

4 to 11 from 80 I

Filler press All appropriate works Use an appliance with

adequate operating

pressure

8 to 15 from 60 I

Pneumatic tools Small drills, rod grinders, etc. As per manufacturer

details

5 to 7 from 180 I

Pneumatic tools

Angular grinder

As per manufacturer

details

5 to 7 from 400 I

Pneumatic tools

Plate shears, sheet cutter, etc.

As per manufacturer

details

5 to 7 from 280 I

Light impact wrenches For screws with a thread within 10

Smaller appliance

enough for short-term

use

5 to 7

from 280 I

Heavy impact

wrenches

For screws with a thread of more

than 10 mm

ditto 5 to 8

from 400 I

Light cutters Cutters for bodies, sheet and small

mason chisels

As per manufacturer

details

5 to 8

from 280 I

Break and blast

hammers

Heavy masonry and concrete

works, tapping

ditto

5 to 10

min. from 460 I

Gun abrasive blasting Only corners, small areas, minor

parts and profiles

ditto

8 to 11 from 300 I

Sandblaster abrasive

blasting

Larger areas and time-consuming

works

ditto

8 to 15 As per manufacturer

details

The above-mentioned values are just of orientation nature as they may differ for appliances of various manufacturers. Works with

higher air requirement may also conditionally be performed with compressors with a lower suction power than the requirement given in

the table. If pressure is reduced in the air jet under the necessary operating pressure, however, an appropriate break must be

introduced after the air jet is pressurised again. In order not to load the compressor when being operated by more than can be

tolerated, we recommend taking into account some power reserve when selecting the right appliance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude Pro 310-10-50 PRO 75505 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info