Bedienungsanleitung Gude Pro 310-10-50 PRO 75505 (Seite 19 von 67) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

628969

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

Failures - Causes - Remedy

CAUTION: FUSES AGAINST OVERHEATING MUST FIRST BE CHECKED!

Failure

Cause Remedy

Compressor does not

start or motor circuit

switch turns off after a

short time at 230 V

appliances:

1. Extension cable is too long or cable cross-

section is too small

2. Defective condensers or relays in the engine

terminal board.

3. Compressor switched off by unplugging.

4. Low outdoor temperature

1. Use the right cable (store it in a warm

environment; fill with 5W40 oil for light running)

2. Contact the customer service centre

3. Deflate the air jet and restart

Compressor does not

start or motor circuit

switch turns off after a

short time at 400 V

appliances:

1. Power line defect

2. Blown fuse

3. Compressor switched off by unplugging

1. Check whether there is power in all 3 phases

(pic. 5.1 Plug connection)

2. Check the protection whether any fuse has not

blown

3. Deflate the air jet and restart

Oil leaks from

compressor:

1. 400 V appliances: Compressor rotation

direction is wrong and oil spirts on the oil filler

neck.

2. Medium obstacle in the cylinder head sealing

is broken through or compressors presses air

to the engine case – oil leaks from the filler

neck or around the oil gauge.

3. Check the oil charge: if the charge is above

the given maximum value, oil may leak in

various places.

4. Check the compressor in all screwed

connections and at sealing and find out where

oil exactly leaks as sealing may get released

to some extent after some time.

5. Attach a piece of paper to the protective grid

and check the rotation direction. If the paper

sticks, the rotation direction is all right. If the

paper is blown away, the rotation direction

may be changed.

6. Caution: Rotation direction may change

when the appliance is operated from any

other outlet.

1. Respect the rotation direction arrow on the

appliance. Change the power line poling.

2. Change the head sealing and tighten the

cylinder head screw after 3 test runs with a force

of max. 50 Nm.

3. Empty oil to the normal level.

4. Tighten the screws above the sealing or order

new sealing and replace the old one.

5. The rotation direction may be changed by

screwing the phase changer. L2 is replaced by

L3 for common plugs.

In an idle state, air is

released from the

compressor oil filler

neck or air is blown

through the discharge

valve on the bottom

part of the pressure

switch:

1. Clack valve is untight or the rubber sealing in

the clack valve is defective.

2. Start-relief valve on the pressure switch is

defective.

1. Open the clack valve cover and check the rubber

sealing state, clean it and order new one if

necessary. Caution: Release air to full extent

first!

2. Contact the customer service centre

Reaching the specified

pressure by the

compressor takes

much longer than

before or is not

reached at all

(take the above-mentioned

steps yourself only if

possessing the necessary

expert knowledge,

otherwise, contact the

customer service centre)

1. Head or valve sealing is defective.

2. Valve membranes are broken through, valve

shims or springs are broken,

3. Valves have been carbonised due to long

operating time.

4. Clack valve is dirty

1. Check and replace if necessary.

2. Check and replace if necessary

3. Carbon deposition. To be cleaned or, better,

replaced.

4. Check and replace if necessary

Other defects or failures

If not possessing the necessary technical or expert qualification, do not experiment. Consult the situation with the customer service or

send the defective parts to be repaired by the manufacturer.

Service

Any technical questions? Complaint? Do you need spare parts or operation manual?

Go to our website www.guede.com and the section Service will help you quickly and without bureaucracy. Please, help us to help

you. In order to identify your device in case of complaint, please indicate serial number, order number and year of manufacture. All

information is available on the product label. To have all information always at hand, put them down.

Serial number:

Order number:

Year of manufacture:

Phone: +49 (0) 79 04 / 700-360 - Fax: +49 (0) 79 04 / 700-51999 - E-Mail: support@ts.guede.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude Pro 310-10-50 PRO 75505 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info