Bedienungsanleitung Gude WS 125-1150 E 58108 (Seite 21 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Türkisch)

624890

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

b) Do not position your body in line with and

behind the rotating wheel. When the wheel, at the

point of operation, is moving away from your body,

the possible kickback may propel the spinning wheel

and the power tool directly at you.

c) When wheel is binding or when interrupting a

cut for any reason, switch o the power tool and

hold the power tool motionless until the wheel co-

mes to a complete stop. Never attempt to remove

he cut-o wheel from the cut while the wheel is in

motion otherwise kickback may occur. Investigate

and take corrective action to eliminate the cause of

wheel binding.

d) Do not restart the cutting operation in the work-

piece. Let the wheel reach full speed and carefully

e-enter the cut. The wheel may bind, walk up or

kickback if the power tool is restarted in the workpiece.

e) Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near

the line of cut and near the edge of the workpiece on

both sides of the wheel.

f) Use extra caution when making a “pocket cut”

into existing walls or other blind areas. The pro

truding wheel may cut gas or water pipes, electrical

iring or objects that can cause kickback.

Safety Warnings Specic for Sanding Operations:

a) Do not use excessively oversized sanding disc

paper. Follow manufacturers recommendations,

when selecting sanding paper. Larger sanding

paper extending beyond the sanding pad presents a

laceration hazard and may cause snagging, tearing of

the disc or kickback.

Additional Safety and Working Instructions

When grinding metal, ying sparks are produced.

Take care that no persons are endangered. Because

of the danger of re, no combustible materials

should be located in the vicinity (spark ight zone).

Do not use dust extraction.

Avoid ying sparks and sanding dust hit your body.

Never reach into the danger area of the machine

when it is running.

Chips and splinters must not be removed while the

machine is running.

Immediately switch o the machine in case of con

siderable vibrations or if other malfunctions occur.

heck the machine in order to nd out the cause.

Do not let any metal parts reach the airing slots -

danger of short circuit!

Under extreme conditions (e.g. smooth-grinding

metals with the arbour and vulcanized bre grinding

wheel), signicant contamination can build up on the

inside of the angle grinder. For safety reasons, in such

conditions the inside should be cleaned thoroughly

of metal deposits and a motor circuit-breaker must be

connected in series. If the motor circuit-breaker trips

the machine must be sent for repair.

For accessories intended to be tted with threaded

hole wheel, ensure that the thread in the wheel is

long enough to accept the spindle length.

Always use and store the cutting and grinding disks

according to the manufacturer‘s instructions.

Always use the correct guard for cutting and grin

ding.

lways use guard with cutting guide from the acces-

sories range for cutting stone.

he adjusting nut must be tightened before starting

to work with the machine.

Always use the auxiliary handle.

The workpiece must be xed if it is not heavy enough

to be steady. Never move the workpiece towards the

rotating disk by hand.

STARTUP PROTECTION

58107: Machines with a lockable switch are supplied

with a restart cutout. This prevents the machine rest

arting by itself after a power failure. When resuming

ork, switch the machine o and then switch it back

on again.

Mains Connection

Operation is only allowed with a safety

switch against stray current (RCD max. stray

current of 30mA).

Connect only to single-phase AC system voltage as

indicated on the rating plate. It is also possible to

connect to sockets without an earthing contact as

the design conforms to safety class II.

Only plug-in when machine is switched o.

Maintenance

Unplug the machine before any work on it.

Repairs and works specied in these Instructions may

only be performed by qualied authorised sta.

Use only original accessories and original spare parts.

Keep the device, in particular the air vents, clean at all

times. Never spray water on the device body!

Do not clean the plastics with solvents, ammable or

toxic uids. For cleaning, use a damp cloth only.

Caution! If the power cord of the appliance gets

damaged, it must be replaced by the manufacturer or

its customer service or a similarly qualied person to

avoid danger.

Only a regularly maintained and treated appliance

can serve as a satisfactory aid. Insucient mainte

nance and care can lead to unforeseen accidents and

injur

ies.

If necessary, a list of spare parts can be found at www.

guede.com.

DEGB

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude WS 125-1150 E 58108 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info