Bedienungsanleitung Gys GYSpack OBD Memory Saver (Seite 8 von 32) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

786854

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

GYSPACK OBD EN

Translation of the original instructions

Disposal:

• This product should be disposed of at an appropriate

recycling facility. Do not dispose of in domestic waste.

• The battery tted in this device is recyclable. Please proceed

according to the applicable recycling regulations.

• The battery must be removed from the device before the

latter is discarded.

GENERAL DESCRIPTION

For 12 V lead-acid batteries (6 x 2 V cells) with a capacity of 30 Ah to 130 Ah.

The GYSPACK OBD is designed to maintain the internal memory of your vehicle during a change of battery or any other

operation involving the disconnection of the battery. This unit prevents any loss of data or the need to reprogram the

on board system (Clock, radio, alarm, hands-free kit…) which can be a long process. Equipped with a cigarette lighter

plug, the GYSPACK OBD is also a 12V DC power supply for Laptops, TVs, tools, etc…

Easy to carry - this product has a compartment to store cables and charger.

To get the maximum from your machine and ensure the long life of the internal battery, it is recom-

mended the unit is charged after each use.

TEST OF THE INTERNAL BATTERY

To start the GYSPACK OBD and test the internal battery health, press the button for 3 seconds. The LEDs will light and

one of these three LED will stay on showing the battery status.

The red light indicates the internal battery is at less than 50% charge,

 It is necessary to charge the internal battery immediately.

The yellow light indicates the internal battery is charged to between 50 and 75%

 You can use the product but it is preferable to charge it as soon as possible.

The green light indicates the internal battery is fully charged.

 The unit is ready to use.

To stop the unit press again the button for 3 seconds. If it doesn’t turn o manually, the unit stops after 4 hours.

RECHARGE OF INTERNAL BATTERY

To charge the internal battery, the GYSPACK OBD must not be connected to a vehicle.

1 - Plug the charger of the unit into the mains supply (230V)

2 - Plug the charger into the indicated place on the front of the machine

3 - State of charge:

The red light indicates the internal battery is charging.

The green light indicates the internal battery is charged.

 You can use the unit.

The yellow light indicates the internal battery is faulty.

 It is necessary to replace the internal battery.

• If after 24 hours of charge the red light is still on, the internal battery is damaged. It is necessary to

replace it.

• Do not try to charge the product via the cigarette lighter connection of your vehicle. The current is

not stable and can damage the product or the cigarette lighter connection. For optimum charge you

must use the charger delivered with the unit and plug it into the mains supply.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gys GYSpack OBD Memory Saver Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info