Bedienungsanleitung Gys GYSpack OBD Memory Saver (Seite 9 von 32) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

786854

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

GYSPACK OBD EN

Translation of the original instructions

If the equipment or the vehicle connected to the GYSPACK OBD needs more than 4A or has a short

circuit, the electronic protection of the GYSPACK OBD will switch on and cut the power supply. To use

it again and enable the protection, it is necessary to disconnect the 12V DC plug or the GYSPACK OBD.

USE ON OBD PLUG

Before using this feature you must be sure that all the energy consumers of your vehicle (fan, lights, onboard compu-

ter…) are switched o:

1 - Check the internal battery of the GYSPACK OBD is charged (read « Test of the internal battery»).

2 - Connect the cable with the OBD connector to the vehicle.

 Check that the connector is properly plugged into the vehicle.

3 - Switch on the product.

4 - Disconnect the battery from the vehicle and put the cables on a non conducting surface.

Attention: The electrical system of the vehicle receives current from the OBD Memory Saver via the OBD plug. However

the battery terminals are still supplied with power. It is necessary to insulate them and avoid any contact with a metallic

part or any conducting object which can create a short circuit.

5 - Once the battery is connected to the vehicle, disconnect the OBD plug.

6 - Charge the product after use.

USE AS A 12V POWER SUPPLY VIA THE CIGARETTE LIGHTER PLUG

This product gives you a 12V power supply via the cigarette lighter plug:

1 - Check the internal battery of the GYSPACK OBD is charged (read « Test of the internal battery»).

2 - Check the equipment that you want to connect to the GYSPACK OBD is switched o then connect the unit via the

cigarette lighter connection.

3 - Switch on the equipment. The GYSPACK OBD will supply the power needed.

4 - Switch o the equipment after each use, disconnect the cigarette lighter connection and plug the GYSPACK OBD

into the mains supply to charge it.

Important: Do not use the OBD plug as a power supply for the on board electronics (onboard computer, radio) because

you can damage the internal battery.

NO WARRANTY ON THE BATTERY

The internal batteries are active components; their life depends on your use and maintenance. The internal batteries

must be charged after EACH use. High temperatures will considerably reduce the battery charge. After a long period

without using the Gyspack OBD, it is recommended to charge the internal batteries again before using.

For this reason the Gyspack OBD battery is not covered under the warranty.

WARRANTY

The warranty covers faulty workmanship for 2 years from the date of purchase (parts and labour).

The warranty does not cover:

• Transit damage.

• Normal wear of parts (eg. : cables, clamps, etc..).

• Damages due to misuse (power supply error, dropping of equipment, disassembling).

• Environment related failures (pollution, rust, dust).

In case of failure, return the unit to your distributor together with:

- The proof of purchase (receipt etc ...)

- A description of the fault reported

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gys GYSpack OBD Memory Saver Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info