Bedienungsanleitung Gys PROGYS 200E FV CEL (Seite 13 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

665728

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

200E FV CEL

INSTALLATION – FONCTIONNEMENT PRODUIT

Only qualied personnel authorized by the manufacturer should perform the installation of the welding equipment.

During set up, the operator must ensure that the machine is unplugged. Connecting generators in a series or a parallel

circuit is forbidden.

HARDWARE DESCRIPTION

These welding are, Inverter, portable welder, for covered electrode and TIG Lift in DC. It allows welding with rutiles,

basic, stainless steel and cast iron electrodes. In TIG, it allows to weld most of metals except aluminium and alloys. It

is protected for a use on electric generators (230V /+- 15%).

POWER SUPPLY – START UP

• This equipment is supplied with a 16 A CEE7 / 7 plug and must be connected to a three-wire 230V (50-60 Hz) single-

phase electrical installation with the earthed neutral. The 200E FV CEL integrates a « Flexible Voltage » system. It has

to be plugged on a power supply variable between 110V and 240V (50 – 60 Hz) WITH earth. The absorbed effective

current (I1eff) is shown on the machine, for maximal using conditions. Check that the power supply and its protection

(fuse and/or circuit-breaker) is compatible with the necessary current during use. In some countries, the change of plug

can be necessary to allow a use at maximal conditions. The welder must be installed so that the main plug is accessible.

• The start-up is done by pressing « »

The device turns into protection mode if the supply voltage is over 265V for the single-phase products (the sсreen dis-

plays ).

Normal operation will resume when the voltage has returned to its nominal range.

CONNECTION ON A GENERATOR

The machine can work with generators as long as the auxiliary power matches these requirements :

- The voltage must be AC, always set as specied, and the peak voltage below 400V,

- The frequency must be between 50 and 60 Hz.

It is imperative to check these requirements as several generators generate high voltage peaks that can damage these

machines.

PRODUCT FEATURES

• The welding machine has a constant voltage output in MMA. Duty cycles

• The duty cycle following the norm EN60974-1 is indicated in the table here below:

X @ 40°C (T cycle = 10 min) MMA (110Veff) MMA (230Veff) TIG (110Veff) TIG (230Veff)

I max 25% @ 120 A 25% @ 200 A 40% @ 140 A 35% @ 200 A

60% 90 A 135 A 120 A 165 A

100% 80 A 115 A 110 A 135 A

While under intensive use exceeding the duty cycle (> to duty cycle) the thermal protection can turn on, in this case, the

machine swictes off and the thermal protection indicator light switches on until the machine returns to normal operting

temperature. The tests have been realized at 40 °C.

Mode MMA

• Your machine is equipped with 3 specic functions to Inverters :

- The Hot Start increases the current at the beginning of the welding.

- The Arc Force increases the current in order to avoid the sticking when electrode enters in melted metal.

- The Anti Sticking allows you to easily withdraw your electrode without damaging it in case of sticking.

MMA WELDING (ELECTRODE) INTERFACE ON PAGE 52

1. Connect cables; electrode holder and ground clip in the connecting connectors,

2. Position the electrode on the electrode holder,

3. Select the MMA position (2) with the selector (5) for 3 sec. (If the TIG mode is activated)

4. Set the desired intensity using the and keys (4). The current is displayed on the digital display (1).

5. Set the «HOT START» and «ARC FORCE» by repeatedly pressing the button (5).

200E FV CEL

HOT START

0 > 90%

ARC FORCE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gys PROGYS 200E FV CEL Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info