665711
19
Zoom out
Zoom in
Vorherige Seite
1/88
Nächste Seite
19
TIG 220 DC / 300 DC
EN
USE WITH EXTENSION CABLES
All extension cables must have an adequate size and section, relative to the machine’s voltage .
Use an extension that complies with national safety regulations.
Current input
Length - Extension selection
< 45m < 100m
TIG 300 DC 400V 2.5 mm²
TIG 220 DC
230V 2.5 mm²
110V 2.5 mm² 4 mm²
SYMBOLS & MENUS
FUNCTION PICTOGRAM
TIG
DC
MMA Comment
HF ignition X TIG process with HF ignition
Lift ignition X TIG process with LIFT ignition
Pre-gas X Time to purge the torch and to protect the area with gas before ignition
Up slope current X Up slope current
Welding current X Second welding current
Courant froid X
Second welding current or «cold» current in standard 4TLOG or in PULSE
mode
PULSE Frequency X X PULSATION frequency of the PULSE mode (Hz)
Down slope current
10s
20s
0s
X
Down slope current to minimum current, I Stop (S) to prevent weld defects
and craters.
Post gas X
Length of time in which gas is released after the arc has stopped. It protects
the weld pool and the electrode against oxidization when the metal is cooling
(S).
HotStart X Adjustable overcurrent at the beginning of the welding (%)
ArcForce X
Overcurrent delivered to avoid sticking when the electrode enters the welding
pool
TIG PULSE X Pulse mode
TIG SPOT X Spot mode
MMA PULSE X MMA process in PULSE mode
2T X 2 time torch mode
4T X 4 time torch mode
4T LOG X 4 time LOG torch mode
Ampere (unit)
A
X X Amperes unit for welding current settings
Volt (unit)
V
X X Volt unit for displaying welding voltage
Second or Hertz (units)
S / Hz
X X Seconds or Hertz unit for time or frequency settings
Percentage (unit)
%
X X Percentages unit for proportionate settings
Display switch A or V
A
V
X X Switches the display of voltage or current during and after welding
Program menu access
MEM
PROG
X X Access to conguration menu (SAVE, JOB, ...)
Thermal protection X X Standard symbol to indicate the thermal protection state
Sleep mode X X Sleep mode
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gys TIG 300 DC wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info