Bedienungsanleitung H2o Steam FX (Seite 6 von 6) (Englisch)

573463

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

DISCONNECT THE UNIT FROM THE POWER OUTLET DURING CLEANING AND MAINTENANCE.

DO NOT IMMERSE THE H2O SteamFX™ HANDHELD STEAMER IN WATER.

Cleaning procedure to remove lime scale

If your H2O SteamFX™ begins to produce steam slower than usual or stops producing steam you may need to remove lime scale. It is necessary to

remove lime scale on a regular basis, every 25 times you use a full tank of water or once a month, especially in areas with hard water.

To remove lime scale from your H2O SteamFX™, please follow these procedures:

Using the Cleaning Pin

Swirl and push the pin up and down the small hole of the steam outlet. Ensure that all scale debris have been removed from the steam outlet

before reassembling any attachment.

Using a cleaning solution

1. Prepare a solution of 1/3 white vinegar and 2/3 water and add to the Water Tank.

2. Ensure that steam released is aimed away from or any surrounding objects. Plug the appliance into a properly grounded electrical outlet, turn it

ON and allow the unit to produce steam until the vinegar/water solution is used up.

3. Repeat the above procedure as many times as necessary until a normal steam flow is achieved.

4. Fill the Water Tank with fresh water and rinse out.

5. Fill the Water Tank with fresh water again, and release steam through the system until the Water Tank is empty.

6. Perform a test cleaning on a suitable isolated area after each lime scale removal to ensure that there is no debris left in the system.

CLEANING AND MAINTENANCE

To clean calcium deposits building up inside the Water Tank:

Add 1-2 tablespoons of white vinegar to a full Water Tank, close the Water Tank cap and shake the contents. DO NOT TURN THE APPLIANCE ON. Let the

unit sit for a few hours. Empty the Water Tank and rinse with clean water until it rinses clear.

Cleaning blocked steamer accessories:

Due to the high mineral content of water in some areas, some calcium buildup might develop inside the tip of the Straight Nozzle. To clean it, we recommend

using a spray lubricant. Spray a small burst or two of the lubricant inside the tip of the Straight Nozzle. After spraying the lubricant, fill the steamer with

water and run a continuous jet of steam through the affected accessory for several minutes to remove the deposit.

WE RECOMMEND PERFORMING THIS PROCEDURE IN A PROTECTED AND WELL-VENTILATED AREA.

Problem SolutionPossible Cause

The unit does not power on

Reduced steam or no steam

Steam escapes from

connections

The unit is not plugged in or turned ON Make sure the unit is plugged into a properly grounded outlet and the

steam switch is pressed

Attachment is improperly connected

Unplug the unit, allow it to cool down, detach the accessories and

reattach them properly

Debris or obstructions at the connection points Remove the accessory and check and clean connection points

Blocked Steam Nozzle

Clean the Nozzle

Water Tank is empty

Fill Water Tank

Lime scale deposit

Follow cleaning procedure to remove lime scale

TROUBLESHOOTING GUIDE

Remember to remove lime-scale at least once a month, especially in areas with hard water.

Please follow instructions provided in this User’s Guide.

Use filtered or distillated water for better performance.

IMPORTANT

WARING

TIPS

OPTIONAL ACCESSORY USAGE

GARMENT STEAMING CLOTH

To steam a garment, place item of

clothing on a hanger and steam the

garment directly. Slowly slide the

Garment Steamer Head vertically over

the garment to smooth the fabric and

remove wrinkles and odors.

Install the Garment Steaming Cloth or microﬁber scrubbing cloth over the Window

Cleaning tool.

Some fabrics like leather, suede, and velvet

may not be suitable for steaming. Please

refer to the manufacturer’s care label.

Curtains and draperies can be steamed

while hanging.

Black Tag

Tag

side

back

Part and Usage Assembly Tips/Caution

EXTENSION HOSE

This 75cm/30” Extension Hose is designed

for use with the following attachments:

- Window Cleaning Tool

- Duster

- Long

Steam Lazer™

Insert the designated end of the

Extension Hose into the designated

hole in the Main Unit and then turn

the locking system.

Make sure the Extension Hose is securely

locked into place before use. When in use,

keep the Extension Hose away from your

body and avoid touching the hose as it

can get hot.

Do not pull the Extension Hose with

excessive force, as it might cause damage

and result in a steam leak.

WINDOW CLEANING TOOL

Attached to the Extension Hose and in

combination with one of the available

cleaning cloths or scraper, use this tool

for window cleaning, garment steaming,

wallpaper removal, etc.

Align the lock button on the Extension Hose

with the designated hole on the Window

Cleaning Tool Frame and push in the

Extension Hose until it locks in place.

Install cleaning cloth of your choice onto the

Window Cleaning Tool.

WINDOW CLEANING CORAL CLOTH

Use it to clean windows, mirrors and glass.

Install the Coral Cloth over the

Window Cleaning Tool. Do not

cover the squeegee blade or scraper

when installing the cleaning cloth.

Make sure to attach the cloth to all

hooks

on the

Clean

ing Tool

Frame

to avoid slipping from the frame

during use.

Do not use steam on frozen windows.

Be careful when using the steamer on

glass, as the glass may break.

Hooks

front

NYLON BRUSH

The round nylon brush is great for

cleaning smooth hard surfaces, such as

toilets, sinks, and kitchen counters, etc.

It can be used with soap or detergent to

clean dirty areas.

Metal/nylon brush can be attached to any of the steam nozzles.

Attach the round metal/nylon brush by screwing onto the threaded end of the Jet

Nozzle or Long

Steam Lazer™

Use different color brushes for particular

cleaning areas (kitchen, bathroom, etc.)

MICROFIBER CLOTH FOR NYLON

BRUSH

Use when you want to pick up the dirt

loosened by the steam.

METAL BRUSH

Can be used on hard surfaces that are not

pron to scratches, i.e. car rims, BBQ, etc.

Place the Microﬁber cloth onto the nylon brush.

LONG STEAM

LAZER™

Easier to clean hard to reach areas (behind

the cabinets, behind the toilet, hard to

reach coners, etc.).

Attach the Long Steam

Lazer™

to the Extension Hose by aligning the lock button on

the Extension Hose with the designated hole on the Long Steam

Lazer™

tool and push

until it locks in place.

Attached to the Extension Hose, the Long Steam

Lazer™

can be used by itself or

with the Round Brush (Nylon). Remove the end cap before installing the Round Brush

(Nylon).

DUSTER WITH CORAL CLOTH

Slowly pass over surface to be cleaned.

The absorbent Coral Cloth picks up the

dirt loosened by the steam.

Install the Coral Cloth into the Duster frame

and attach the Duster to the Extension Hose.

MICROFIBER SCRUBBING CLOTH

Removes more dust and dirt with less

effort. Effective in cleaning stubborn

smudges or spills.

Hooks

BENDABLE JET NOZZLE

Cleans tight corners and hidden places.

Screw the Bendable Jet Nozzle onto the Long Steam Lazer

™

. Remove the black

plastic cap from the top of the Long Steam Lazer

™

. Replace the plastic cap after

attaching the Bendable Jet Nozzle.

H2o Steam FX Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info