Bedienungsanleitung Habitat IONFLOW 50 (Seite 5 von 44) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

478217

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

4: Finally, plug the transformer cable into the switch plug in

the transformer plug

The indication light should light up. Congratulations!

From now on, you are breathing cleaner air.

5: To switch the IonFlow 50F & 50F Style on and off:

• Air purier ON (upper indication light on) & decorative light

OFF

• Air purier ON (upper indication light on) & decorative light

• Air purier OFF (upper indication light off) & decorative

light OFF

6: The decorative lights can be changed easily.

4B. Assembly and installation of 50C

S E E P I C T U R E S O N PA G E 3 3

Assemble the air purier in the following order:

For ceiling installation: Drill an 8mm hole in the ceiling to

attach the wall plug and ceiling hook. Insert the plug into the

hole and screw in the ceiling hook.

For suspended ceilings: Consult an electrician for the most

appropriate solution

NB. Ensure that the distance from the wall to the air purier

is at least 3 feet / 1 metre

A-D: Thread the cable through the loops of the pressure

relief device.

E-F: Attach the pressure relief device to the top of the ion

generator (at the outlet on the plastic tube) and ensure that it

snaps into the holes

G: Connect the plug to socket on the ion generator

H: Attach the cable to the pressure relief hook. The air puri-

er should hang down at least 2 feet / 60 cm from the ceiling

I: Hang the pressure relief hook from the ceiling hook

J-K: Hold the metal hook on the ion generator. Then care-

fully lift the collector (aluminium cylinder) from underneath

(where the corona needles are) up and over the metal hook

L: Then let the collector slide back down and rest on the

metal hook. NB. This connection is vital in order for the air

purier to function.

• Finally, plug in the transformer plug at the wall socket. If

an extension lead is required, attach this to the transformer

cable.

The indication light should light up. Congratulations!

From now on, you are breathing cleaner air.

5. Cleaning and maintenance

• Always unplug the transformer plug before cleaning the air

purier.

• Do NOT wash the collector in the dishwasher.

• Do not use cleaning products that contain alcohol solutions,

ammonia or alkaline substances, as these products may

damage the air purier.

• The collector should be cleaned around once a week or as

and when required. The collector may require more frequent

cleaning if used in highly contaminated environments.

Cleaning the collector:

IonFlow 50F & 50F Style: Remove the collector by lifting up

the ion generator with the collector attached. Then hold in

the metal hook and pull the collector downwards (pictures

1-3 on page 32, in reverse). NB. The ion generator may be

damaged if you pull it upwards!

IonFlow 50C: Hold in the metal hook on the ion generator

and move the collector down (pictures J-L on page 33, in

reverse)

1. Clean the collector with washing-up liquid, warm water

and a soft sponge/dish brush

2. Dry the collector with a dishtowel

3. Put the collector back on the ion generator according to

the earlier instructions.

If you have followed all the above instructions but the col-

lector is not clean, try the following:

1. Spray cleaning uid onto the collector and let it work for

5 minutes

2. Using a damp sponge, rub any remaining spots until they

disappear

3. Wipe the collector using a clean, damp sponge

4. Dry the collector with a towel and place it back on the ion

generator according to the earlier instructions.

5. Repeat the above procedure if necessary

Cleaning the ion generator, corona needles and acrylic

stand:

• Once every four months you may need to carefully clean

the fragile corona needles. Use a small brush (e.g. a

toothbrush) and carefully brush away the thin layer of white

lime scale and dirt which may have become attached to the

needles. Do not use pressure or water when you clean the

needles.

• Clean the ion generator and the acrylic stand with cleaning

spray and a damp cloth or sponge. Wipe clean and rub away

any remaining dirt. Dry with a towel. Do not allow the top and

bottom to come into contact with water and be careful with

the corona needles on the ion generator.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Habitat IONFLOW 50 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info