Bedienungsanleitung Hama CDR70BT (Seite 12 von 19) (Englisch)

723748

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

4.1 Antenna connection / alternative solutions

(Figure D)

Note

• To optimise reception, the glass adhesive antenna

should be tted such that it is in contact with the

vehicle body.

• If your vehicle’s A pillar is covered with fabric or other

insulating material, t the metal foil there anyway.

• Consult a local car workshop regarding the antenna’s

contact with the vehicle body.

• Fit the antenna at the edge of the windscreen (preferably

on the passenger side) and connect the metal foil to your

vehicle’s A pillar.

• Then connect the SMB connector of the antenna cable to

the antenna input (14) of the adapter.

Note

• The included glass adhesive antenna can be replaced

by an alternative antenna solution.

• The existing vehicle antenna can continue to be used

with an adapter.

• Consult a car workshop or visit www.hama.comfor

suitable accessories.

4.2 Mounting

Warning – Risk of injury

• Take care that components such as airbags, safety

areas, controls, instruments, etc. and visibility are not

blocked or restricted.

• Do not allow yourself to be distracted by the product,

for example when driving a vehicle or operating sports

equipment. Always pay attention to the surrounding

trac and your environment.

Note

• Before mounting the holder, check the installation

options in your vehicle. If in doubt, consult the manual

for your vehicle or contact the manufacturer.

• Strictly avoid using undue force when using the

product or during installation.

A) Mounting to ventilation grille

• Fit the mounting adapter for ventilation apertures to the

back of the product. (Figure A)

• Now insert the device into the ventilation grille.

• The peg for the mount in the ventilation grille can be

turned 360° so that you can adjust alignment.

B) Mounting using the adhesive pad

Note – Mounting surface

Please note that the selected mounting surface (e.g.

dashboard) should be free of dust and grease. Use a

suitable cleaning agent from a specialised dealer to

clean the surface.

• Fit the mounting adapter with the adhesive pad to the

back of the product (Figure B).

• Clean the surface to which the adhesive pad is to be

axed.

• Now remove the protective lm from the adhesive pad

and mount the adapter on the chosen surface.

4.3 Connection

Note

• Only use original accessories (or accessories approved

by Hama), to prevent damage to the product.

• Connect the supplied USB charging cable to the USB port

(16) of the device.

• Connect the unused plug on the USB cable to a 12 V

socket of your vehicle.

4.4 Switching on / Standby / Initial setup

Switching on the product

• Press and hold [

](2) for about 3 seconds to switch on

the device.

Switching off the product

• Press and hold [

] (2) for about 3 seconds to activate

the standby mode.

Note

To switch off the radio completely, disconnect it from the

power supply.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hama CDR70BT Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hama CDR70BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info