813561

HammerSmith M22606 Multitool Seite 16

16
Zoom out
Zoom in
Vorherige Seite
1/64
Nächste Seite
16
17
The battery can be left in the charger; in this case
the LED display is lit green continuously. The charger
keeps the battery pack in a fully charged state.
INSTALLATION AND REMOVAL OF THE BATTERY
PACK IN/FROM THE DEVICE
WARNING: Make sure that the rotational
direction switch is in the middle position to
avoid triggering the switch while removing
or installing the battery pack.
INSTALLATION
Slide the battery pack into the device until it clicks
into place. Make sure that the battery pack is correctly
positioned and fully engaged. (see Figure 7/A+B)
REMOVAL
Press the battery pack release button and pull the
battery out of the device.
ATTACHING THE TOOLS
WARNING: TO AVOID THE RISK OF INJURY,
REMOVE THE BATTERY PACK FROM THE
TOOL BEFORE MAKING ANY
ADJUSTMENTS, REMOVING AN ATTACHMENT OR
INSTALLING A NEW ACCESSORY.
Make sure that the lower edge of the respective
tool attachment and power section of the base
device are aligned horizontally and then push the
attachment into the device until it clicks into place.
(see Figure 8/A-C)
REMOVING THE TOOLS
Slide the locking switch down to release the tool
from its docking place, then pull the attachment
forward and away.
ON/OFF AND ROTATIONAL DIRECTION SWITCH
• The device is switched on and off by pressing and
releasing the ON/OFF switch. The harder the ON/OFF
switch is pressed, the faster the rotational speed.
• The direction of rotation switch is used to set the
direction of the drill chuck forward for screwing in
screws or backward for their removal. It is located
above the variable ON/OFF switch.
• To select the forward direction of rotation, press the
direction switch to the left (when viewed from the
rear).
• To select the backward direction of rotation, press
the direction switch to the right (when viewed from
the rear).
NOTE: When changing the position of the rotation
direction switch, make sure that the ON/OFF switch
for speed control is not pressed in.
WORKING WITH THE DRILL ATTACHMENT
Secure the device against being switched on
accidentally by moving the direction switch
(into the middle position). There is a risk of
injury if the device switches on unintentionally.
1. Turn the chuck anti-clockwise until the drill opening
is large enough to insert the tool (drill bit holder).
2. Insert the tool as far as possible into the chuck.
3. Turn the chuck clockwise to clamp the tool.
4. To remove the tool, turn the chuck anti-clockwise
and pull it out of the drill hole.
Selection of the desired operating mode
You can use the torque setting ring to adjust the
power produced by the screwdriver.
1 - Low power
19 - High power
A. Drilling:
When ready to drill, set the torque adjustment
ring to the drill setting. Insert the drill set
corresponding with the material into the chuck.
You can use for drilling into wood, metal,
plastic, cement, ceramics or any other similar or
comparable material.
B. Screwing: If you want to use for screwing, set the
torque adjustment ring to the appropriate torque
setting. Before choosing the setting, pay attention
to the material you want to screw into. Insert the bit
extension or the flexible bit holder into the chuck.
You can use it to attach different screws and parts.
Setting the direction of rotation
The direction of rotation of the device can be
changed using the rotational direction switch.
(see Figure 2)
1. Wait until the device has come to a standstill.
2. Move the direction switch to the desired position:
Clockwise direction of rotation: → for drilling and
screwing in screws.
Anti-clockwise direction of rotation: ← for
removal of screws.
3. When you move the direction switch to the
middle position, the device is secured against
being switched on unintentionally. The direction
of rotation may only be changed when the
machine is at a standstill.
WORKING WITH THE OSCILLATION ATTACHMENT
Secure the device against being switched
on accidentally by moving the direction
switch (into the middle position).
M22606_HammersmithMultitool_Manual_V03_20220629_MM.indd 16M22606_HammersmithMultitool_Manual_V03_20220629_MM.indd 16 20.07.22 12:2120.07.22 12:21
… 16 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für HammerSmith M22606 Multitool wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info