Bedienungsanleitung Harman Kardon AVR 135 (Seite 16 von 48) (Englisch)

8522

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

16 SYSTEM CONFIGURATION

SYSTEM CONFIGURATION

16 SYSTEM CONFIGURATION

Input Setup

The first step in configuring the

AVR 135 is to configure

each input. Once an input is configured,

all settings for

the Digital Input, Surround Mode and Delay Timing will

“attach” themselves to that input and be stored in a

nonvolatile memor

y. The later selection of that input

will automatically recall those settings

. For that reason,

the procedures described below must be repeated

for each input source so that you have the opportunity

to customize each source to your specific listening

requirements

. However, once made, they need not be

changed again unless you need to alter a setting

When using the full-OSD system to make the setup

adjustments, press the

OSD Button v once so that

the

MASTER MENU (Figure 1) appears. The

›

cursor will be next to the INPUT SETUP line.

Press the

Set Button p to enter the menu and the

INPUT

SETUP

menu (Figure 2) will appear on

the screen. Press the

‹

›

Buttons o until the

desired input name appears in the highlighted video,

as well as being indicated in the front-panel

Input

Indicators

ı. If the input will use the standard left/

right analog inputs, no further adjustment is needed.

Figure 2

If you wish to associate one of the digital inputs with

the selected input source, press the

Button n

on the remote while the INPUT

SETUP

(Figure 2) is on the screen, and the on-screen cursor

will drop down to the

DIGITAL IN line. Press

the

‹

›

Buttons o until the name of the desired

digital input appears

o return to the analog input,

press the buttons until the word

ANALOG appears.

When the correct input source appears

press the

Button n once so that the

›

cursor appears next

BACK TO MASTER MENU, and press the

Set Button p.

To change the digital input at any time using the dis-

crete function buttons and the semi-OSD system,

press the

Digital Select

Button

q on the remote

Within five seconds, make your input selection using

the

⁄

Buttons n until the desired digital or

analog input is shown in the

Upper Display Line ˜

and in the lower line of the on-screen display. Press

the

Set Button p to enter the new digital input

assignment.

Some digital video input sources, such as a cable box

or HDTV set-top

, may change between analog and

digital outputs, depending on which channel is in use.

The AVR 135’s Auto Polling feature allows you to

avoid losing the audio feed when this happens by

permitting both analog and digital connections to

the same source on the AVR. Digital audio is the

default, and the unit will automatically switch to the

analog audio if the digital audio stream stops.

In cases where only a digital source is used, you may

wish to disable the

Auto Polling feature to prevent the

AVR from trying to “find” an analog source when the

digital source is paused. To turn Auto Polling off for

any input, first make certain that the

›

cursor is point-

ing to the

AUTO POLL line on the menu screen.

Next, press the

‹

›

Navigation Buttons o so that

OFF appears. Repeat the procedure at any time so

that

ON appears to restore the Auto Polling feature.

When all needed adjustments have been made, press

the

Button n until the

›

cursor is next to

BACK TO MASTER MENU to continue with

the system configuration.

Surround Setup

he next step is to set the surround mode you wish

to use with the input that was previously selected in

the

INPUT SETUP menu. Since surround

modes are a matter of personal taste, feel free to

select any mode you wish – you may change it later.

However, to make it easier to establish the initial

parameters for the AVR 135, it is best to select Dolby

Pro Logic II or Logic 7 for most analog inputs and

Dolby Digital for inputs connected to digital sources.

In the case of inputs such as a CD Player, Tape Deck

or Tuner, you may wish to set the mode to Stereo

(“Surround off

”) as they are not typically used with

multichannel program material, and it is unlikely that

sur

round-encoded material will be used. Alternatively,

the

Logic 7 Music mode is a good choice for stereo-

only source material. See page 24 for more informa-

tion on available surround modes

When selecting surround modes for digital program

material,

the AVR 135 will always examine the data

stream and automatically select Dolby Digital or DTS

as applicable.

It is easiest to complete the surround setup using the

full-OSD on-screen menus

. From the

MASTER

MENU (Figure 1), press the

⁄

Buttons n

until the

›

cursor is next to the SURROUND

SELECT line

. Press the

Set Button p until the

SURROUND SELECT menu (Figure 3) is on

the screen.

Figure 3

Each of the option lines on this menu (Figure 3)

selects the surround mode category, and within each

of those categories there will be a choice of the

specific mode options. The choice of modes will

vary according to the speaker configuration in your

system. When the

SURR BACK line of the

SPEAKER SETUP menu (Figure 5 on page

18) is set to

NONE, the AVR 135 will be configured

for 5.1-channel operation, and only the modes appro-

priate to a five-speaker system will appear. When the

SURR BACK line of the SPEAKER

SETUP

menu (Figure 5) is set to SMALL or

LARGE the AVR 135 will be configured for

6.1/7.1-channel operation, and additional modes

such as Dolby Digital EX and DTS-ES will appear, as

they are only available when six main speakers are

present. In addition, some of the modes available in

the AVR 135 will not appear unless a digital source is

selected and is playing the correct bitstream.

Remember that when you use only a single, surround

back speaker, you will get the benefits of a 6.1/7.1

system, but with only one speaker installed at the back

of the room. The mode indications will show 7.1 in

some cases, but no additional adjustment is needed

for 6.1 operation. Remember that the AVR 135 will

combine the left and right surround back channel

information present in 7.1 modes such as Logic 7/7.1

and 7-channel stereo

outputting the information as a

single surround back channel.

o select the mode that will be used as the initial

default for an input,

first press the

⁄

Buttons

n until the on-screen cursor is next to the desired

mode’s master category name, such as

DOLBY,

DTS, DSP

(SURR)

or VMAX.

Next,

press

the

Set Button p to view the sub-menu. Press the

‹

›

Buttons o to scroll through the available

choices, and then press the

Button n so that

the cursor is next to

BACK TO MASTER

to continue the setup process.

** SURROUND SELECT **



DOLBY SURROUND

DTS

LOGIC 7

DSP (SURR)

VMAX

STEREO

BACK TO MASTER MENU

* INPUT SETUP * 



INPUT :VIDEO 1

DIGITAL IN:ANALOG

AUTO POLL :OFF



BACK TO MASTER MENU



AVR 135 OM 12/3/04 12:11 PM Page 16

Ich brauche die Anleitung für Harmann Kardon AVR 135 in deutscher Sprache. Wo kann ich sie bekommen? Eingereicht am 13-12-2022 09:01
Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.

Neu registrieren

Registrieren auf E - Mails für Harman Kardon AVR 135 wenn:

neue Frage gestellt werden
neue Handbücher vorhanden sind

Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.

Andere Handbücher von Harman Kardon AVR 135

Harman Kardon AVR 135 Bedienungsanleitung - Holländisch - 42 seiten

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.

Harman Kardon AVR 135 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 135

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info