Bedienungsanleitung Harman Kardon AVR 1510 (Seite 22 von 47) (Englisch)

534559

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

AVR

While making adjustments, you can measure the channel levels in one of these ways:

Preferably, use a handheld SPL meter set to the C-weighting, slow scale. Adjust each Ř

speaker so that the meter reads 75dB when the AVR’s built-in test noise is playing.

By ear. Adjust the levels so that the test tone sounds equally loud to you when it plays Ř

through each speaker.

To set your levels using the AVR’s internal test tone, select the menu’s Test Tone line and

use the Left/Right buttons to turn the test tone on. Then select the Test Tone SEQ line to

select between Auto and Manual:

Auto: The test tone will automatically circulate to all speakers, as indicated by the

highlight bar. Use the Left/Right buttons to adjust the level for any speaker when the test

tone is paused there. Use the Up/Down buttons to move the highlight bar to another line,

and the test tone will follow the bar. To stop the test tone, use the Up/Down buttons to

move the cursor out of the screen’s speaker listings area.

Manual: The test tone will stay on the selected speaker until you use the Up/Down

buttons to move it to another speaker. Use the Left/Right buttons to adjust the level for

the speaker through which the test tone is playing.

If you are using an external source to set your output levels, set Test Tone to Off, use the

Up/Down buttons to navigate to each speaker, and use the Left/Right buttons to adjust

the speaker’s level while the source plays.

NOTE: If you are using a handheld SPL meter with external source material, such as a

test disc or an audio selection, play it and adjust the AVR’s master volume control until

the meter measures 75dB. Then adjust the individual speaker levels.

Output Reset: To reset all levels to their factory defaults of 0dB, scroll down to this line

and press the OK button.

When you have ﬁnished adjusting the speaker levels, record the settings in Table A2 in

the Appendix. Then press the Back/Exit Button.

Notes on Setting Speaker Volumes in Home Theater Systems:

While setting your system’s individual speaker volume levels is ultimately up to your

personal taste, here are some ideas you may ﬁnd helpful:

For ﬁlms and video-music programs, your overall goal should be to create an Ř

enveloping, realistic sound ﬁeld that draws you into the ﬁlm or music program

without drawing your attention away from the action on the screen.

For multichannel music recordings, some music producers will create a sound ﬁeld Ř

that places the musicians all around you; others will create a sound ﬁeld that places

the musicians in front of you, with more subtle ambience in the surround speakers

(as you would experience in a concert hall).

In most multi-channel ﬁlm soundtracks, the surround speakers are not intended Ř

to be as loud or as active as the front speakers. Adjusting the surround speakers

so they are always as loud as the front speakers could make dialogue difﬁcult to

understand and will make some sound effects sound unrealistically loud.

Notes on Setting Subwoofer Volume:

Sometimes the ideal subwoofer volume setting for music is too loud for ﬁlms, while Ř

the ideal setting for ﬁlms is too quiet for music. When setting the subwoofer volume,

listen to both music and ﬁlms with strong bass content and ﬁnd a “middle ground”

volume level that works for both.

If your subwoofer always seems too loud or too quiet, you may want to place it in Ř

a different location. Placing the subwoofer in a corner will always tend to increase

its bass output, while placing it away from any walls or corners will always tend to

reduce its bass output.

Set Up Your Sources

The Source Setup menu lets you assign the correct physical audio and video connections

to each source and lets you set many audio and video playback features for each source.

IMPORTANT: The “Video In” and “Audio In” settings are not optional and must

be adjusted before you use your AVR to enable playback of each source.

You can

adjust the other settings later. See System Settings, on page 29, for complete information

about adjusting all of the Settings menu options.

1. Review the input connections you listed on the Source Buttons and Assigned

Connectors table, on page 15. Note what changes (if any) you want to make from the

default connector assignments that appear on the list.

2. Turn on your TV and select the TV input where you connected the AVR in Connect Your

TV or Video Display, on page 14.

3. Press the remote control’s OSD/Menu button. The AVR’s OSD setup menu will appear

on the TV. (Note: If you have used a composite video connection to your TV, the OSD

menus will not appear on your TV. Follow the steps below using the AVR’s front-panel

display.)

4. Use the remote’s arrow and OK buttons to select “Source Setup,” and use the left/right

arrow buttons to select a source button with connectors that you want to re-assign.

5. Select “Video In” and select the video input connector you want to assign to the source

button. Press the OK button. NOTE: If you select an HDMI connector as the video input

connector, the audio input connector will automatically change to the same HDMI

connector. You cannot use a different audio input connector with an HDMI video input

connector.

Set Up the AVR

Harman Kardon AVR 1510 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 1510

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info