Bedienungsanleitung Harman Kardon AVR 1510 (Seite 23 von 47) (Englisch)

534559

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

ENGLISH

AVR

Set Up the AVR and

Operating Your AVR

6. If you have not selected an HDMI connector for Video In, select “Audio In” and select the

audio input connector you want to assign to the source button. Press the OK button.

7. Press the remote’s Back/Exit button and repeat steps 3 – 6 for the remaining source

buttons with connectors you want to re-assign.

Title: This selection lets you change the display name for the source, which is useful if

your source’s device type is different from the source’s preprogrammed name. Use the

Up/Down buttons to scroll forward or backward through the alphanumeric characters

until the desired character appears, then use the Left/Right buttons to move the cursor to

the next or previous position. Move the cursor again to leave a blank space. (Your name

can have a maximum of 10 characters.) When you have ﬁnished, press the OK Button.

The new name will appear on the AVR’s front panel and throughout the on-screen menu

system.

Tone: This setting determines whether the treble and bass controls are active for the

source. When it’s set to Off, the tone controls are out of the circuit, with no changes to the

sound. When it’s set to On, the bass and treble controls are in the circuit.

Treble/Bass: These settings boost or cut the treble or bass frequencies by up to 10dB,

in 2dB increments. Use the Left/Right buttons to change the setting. The default setting

is 0dB.

Night Mode: This setting activates Night mode for the source, which works with specially

encoded Dolby Digital discs or broadcasts. Night mode compresses the audio so that

louder passages are reduced in volume to avoid disturbing others, while dialogue remains

intelligible. The following settings are available:

Off: No compression is applied. Loud passages in the program remain as they were Ř

recorded.

Mid: Loud passages in the program are reduced moderately in volume.Ř

Max: Loud passages in the program are reduced more in volume.Ř

Lip Sync: This setting lets you resynchronize the audio and video signals from the source

to eliminate a “lip sync” problem. Lip-sync issues can occur when the video portion of a

signal undergoes additional processing in either the source device or the video display.

Use the Left/Right buttons to delay the audio by up to 180ms. (The active source’s video

will be visible behind the OSD menu, allowing you to synchronize the audio with the

picture.)

You can also make lip sync adjustments without activating the AVR’s OSD menus.

Pressing the remote’s Delay button will display the Lip Sync menu bar on the TV,

superimposed at the bottom of the video. Use the Left/Right buttons to delay the audio

until it is synchronized with the picture.

Set Up the Network

To play MP3 or WMA media located on DLNA-compatible devices connected to the

network or use the AVR’s internal Internet radio tuner, the AVR must be connected to

your home network.

If your network uses an automatic IP address, you should not have to perform any

network setup procedures. Once you connect the AVR to your home network, the network

should automatically assign the AVR an IP address, and the AVR should automatically join

your network.

If your AVR does not automatically join your network (in which case the AVR will display a

“Not Connected” message when you press the Network source button):

1. Press the OSD/Menu button, select System Setup, then select Network.

2. The Network menu will appear.

3. Select IP Conﬁguration, then press the Right button button twice to cycle the setting

from “Auto” to “Manual” and back to “Auto.”

4. Scroll down to the bottom of the page, then press down once more. Select “Apply &

Save”. The AVR will attempt to connect to the network.

5. If the AVR again fails to connect to the network, you may need to enter your network’s

settings manually. In this case, you may need to obtain your network’s settings from

your ISP or network administrator. After obtaining your network’s settings:

Select IP Conﬁguration and use the Left/Right buttons to change the setting to a)

“Manual.” The following settings will become active: IP Address, Subnet Mask,

Gateway, Primary DNS and Secondary DNS

Use the Up/Down buttons to select the correct numbers and make entries for all b)

of these settings.

When you have ﬁnished, scroll down to the bottom of the page, then press down c)

once more. Select “Apply & Save,” and press the OK button. The AVR will refresh

the network connection while it remains on. If the AVR cannot connect to the

network using the manual settings, contact your ISP or network administrator for

assistance.

IMPORTANT: You must select “Apply & Save” for your network settings to take

effect.

NOTE: We recommend that you directly connect the AVR to a home-network router so

that it can directly access the Internet for Internet radio, or access devices on the network

for playback of content stored on the devices (see Listening to Media via Your Home

Network, on page 26, for more information).

NOTE: If you have trouble connecting to the network at any time, cycle the AVR into

the Off mode, and then turn it back on.

Operating Your AVR

Now that you have installed your components and completed a basic conﬁguration, you

are ready to begin enjoying your home theater system.

HARMAN Remote App

For easy control of your AVR with your hand-held device, download the free Harman

Kardon Remote app from iTunes App Store for compatible Apple products, or from Google

Play for compatible Android powered smartphones.

The Harman Kardon Remote App controls virtually all the functions of AVR 1510 and

AVR 151 AVRs that are connected to the same network as the device that has the app

installed. With this easy-to-use app you can turn the AVR on or off, select a source,

control the volume and virtually any other function. You can also access and navigate all

of the AVR’s on-screen setup menus.

Harman Kardon AVR 1510 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 1510

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info