Bedienungsanleitung Harman Kardon AVR 265 (Seite 37 von 62) (Englisch)

502603

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

AVR

ENGLISH

Manual Speaker Setup

If you have already run the EzSet/EQ process as explained in

Conﬁgure the AVR for Your

Speakers

, on page 25, the AVR saved the results. To ﬁne-tune the EzSet/EQ results, or to

conﬁgure the AVR from scratch, select Manual Setup. A screen similar to the one shown

below will appear.

Sub

Number of Speakers

Level Adjust

Crossover (Size)

Distance

Sub Mode:

Reset

Manual Speaker Setup

NOTE: All of the speaker setup submenus include the Back option. To save the current

settings, select the Back option.

To reconﬁgure the speakers from scratch, select the Reset option.

For best results, adjust the submenus in this order: Number of Speakers, Crossover (Size),

Sub Mode, Distance and Level Adjust.

Number of Speakers

This selection lets you program the correct setting for each speaker group. The settings

in this menu affect the remainder of the speaker setup process and the availability of

various surround modes at any time.

Select ON when the speakers are present in the system; select OFF for positions where

no speakers are installed. The Front Left & Right setting is always ON and may not be

disabled.

Front Left & Right

Center

Surr. Left & Right

Assigned AMP

Sub

Manual Speaker Setup

Number Of Speakers: 7.1

Surr. Back

Any changes will be reﬂected in the total Number Of Speakers displayed at the top of

the screen.

The Assigned AMP setting includes four options:

Surround Back: • Select the Surr. Back option if your main system is a 7.1-channel

system and you are using surround back left and surround back right speakers.

Zone 2: • Select the Zone 2 option if your main system is a 5.1-channel system and

you want to use the Assigned Amp speaker outputs to power speakers in Zone 2. See

Install a Multizone System

, on page 21, for more information.

Front Height: • Select the Front Height option if your main system is a 7.1-channel

system and you are using Front Height speakers with Dolby Pro Logic IIz.

Off: • Select Off if you have not connected speakers to the Assigned Amp speaker

outputs.

NOTE: When you set Assigned AMP to “Zone 2,” the speakers connected to the Assigned

Amp outputs will not be conﬁgured during the EzSet/EQ process. Conﬁgure the speakers

manually, as explained below.

When you have ﬁnished, select the Back option or use the Back/Exit button.

Crossover (Size)

After you return to the Manual Speaker Setup menu, navigate to the Crossover (Size) line

and press the OK button to display the Adjust Crossover Frequencies menu.

Front Left & Right

Center

Surr. Left & Right

Surr. Back L & R

Sub Size

Reset Crossover

Manual Speaker Setup

Adjust Crossover Frequencies

12 inch

80 Hz

100 Hz

The AVR will display only those speaker groups you set to On in the Number of Speakers

menu.

Refer to Table A3 for each speaker’s crossover frequency.

For each speaker group, select one of these eight crossover frequencies: Large, 40Hz,

60Hz, 80Hz, 100Hz, 120Hz, 150Hz or 200Hz. If the speaker’s crossover frequency is

below 40Hz, select the ﬁrst option, “Large.” This setting doesn’t refer to the speaker’s

physical size but to its frequency response, which is also called “full range.”

Specify the size of the subwoofer’s transducer as 8, 10, 12 or 15 inches. The AVR always

sets the subwoofer crossover to 100Hz but uses the transducer size for equalization.

Write down the settings in Table A6 in the Appendix.

When you have ﬁnished entering the settings, select Back or press the Back/Exit

button.

Sub Mode

Move the cursor to the Sub Mode line. This setting depends upon the Crossover setting

you selected for the front left and right speakers.

If you set the front speakers to a numeric crossover frequency, the subwoofer setting •

will always be SUB. All low-frequency information will always be sent to the subwoofer.

If you don’t have a subwoofer, either upgrade to full-range front left and right speakers

or add a subwoofer at the earliest opportunity.

If you set the front speakers to LARGE, select one of the three following settings for •

the subwoofer:

L/R+LFE: This setting sends all low-frequency information to the subwoofer,

including a) information that would normally be played through the front left and

right speakers and b) the special low-frequency effects (LFE) channel information.

OFF: Select this setting when no subwoofer is in use. All low-frequency information

will be sent to the front left and right speakers.

LFE: This setting plays low-frequency information contained in the left and right

program channels through the front left and right speakers, and directs only the

LFE-channel information to the subwoofer.

0295CSK - HK (x65Series) AVR3650_365_2650_265 CORE OM, WORK18 danny.indd 37 01/07/11 11:34:08

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR 265 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 265

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info