Bedienungsanleitung Harman Kardon AVR 265 (Seite 39 von 62) (Englisch)

502603

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

AVR

ENGLISH

Manual Speaker Setup, System Settings

Listening in Zone 2

With the multizone system in use, you may enjoy an exciting 5.1-channel home theater

presentation in the main listening area, while others listen to the same program or an

entirely different source in another room. See

Install a Multizone System

, on page 21, for

installation information.

You control the AVR’s multizone system from the on-screen Zone 2 menu. Press the

Setup button, and use the Up/Down buttons to navigate to the Zone 2 line. Press the OK

button to display the Zone 2 menu.

Zone 2

Status:

Source:

Volume:

Assigned AMP:

Off

FM Radio

Zone 2

Status: This line lets you turn Zone 2 on or off.

Source: This line lets you select the source input for Zone 2. You may select a different

source from the one currently operating in the main listening area. However, if the same

source has been selected for both the main listening area and Zone 2, listeners in both

areas will hear the same content.

NOTE: Only analog audio sources, including The Bridge IIIP and USB devices, are

available to the multizone system. To hear digital devices such as a CD player in

Zone 2, follow these steps:

In addition to making a digital audio connection, connect the source device’s analog 1.

audio outputs to the AVR. Make a note in Table A5 on page 47 to record which set of

analog inputs you used.

In the Info menu, scroll down to the Zone 2 Audio setting and select the analog audio 2.

input. (Leave the Audio Input From Source set to the digital input.)

Volume: Highlight this line, and use the Left/Right buttons to control the volume in

Zone 2.

Assigned AMP: This line lets you assign the Assigned AMP channels to “Zone 2”

for multizone operation (see

Number of Speakers

, on page 37). When this line is set

to Zone 2, you may conﬁgure the main listening room for only up to 5.1 channels.

To operate the multizone system using the main remote, slide the Zone Select Switch at

the bottom of the remote to the “2” position.

AVR 3650/AVR 365 only: To select a zone using the Zone 2 remote, press the Zone

Selector, and the Zone Indicator light will turn green when the remote is set to operate

Zone 1 or red to operate Zone 2.

System Settings

The AVR’s System Settings menu lets you customize in what way many of the AVR’s

features operate. Press the Setup button and navigate to the System line. Press the OK

button to display the System Settings menu.

System Settings

Front Panel Settings

Front Panel Dimmer:

On 100%

Auto

Off

HDMI Settings

HDMI Audio to TV:

HDMI Control:

Audio Return Channel:

Power Control:

TV Control:

General A V R Settings

Network Settings

Volume Units:

Volume Default:

Volume Default Level

System Settings

Unit of Measure:

Language:

Dolby Vol. Calibration:

RS232 Control:

Feet (ft)

English

Off

24-02-2011 03

Medium

3 seconds

30 seconds

5 minutes

10 minutes

Menu Appearance

Menu Transparency:

Volume/Status Messages:

Menus:

Setup and Slide-In Menus:

Screen Saver:

System Info

Software Version:

Upgrade Software:

Front-Panel Dimmer: This control sets the brightness of the AVR’s front-panel message

display. Select from 100%, 50%, 25% or Off. The light inside the Volume Control will go

out when the display is partly or fully dimmed, but the Power Indicator will always remain

lit to remind you that the AVR is powered on.

HDMI Settings

HDMI Audio to TV: This setting determines whether HDMI audio signals are passed

through the HDMI Monitor Out connector to the video display. In normal operation, leave

this setting at Off, as audio will be played through the AVR. To use the TV by itself, without

the home theater system, turn this setting to On. In this case you will need to mute the

TV’s speakers (or switch the setting to Off) when using the AVR for audio.

HDMI Control: This setting allows the communication of control information among the

HDMI devices in your system. Turn this setting to On to allow control communication

between the HDMI devices; turn the setting to Off to forbid control communication.

Audio Return Channel: Selecting “Auto” will send audio from the TV to the AVR via the

HDMI Audio Return Channel (ARC) connection (which is in the HDMI cable connecting

the AVR to the TV). The TV source’s “Audio Input from Source” will be automatically

reassigned to the HDMI ARC connector. This way, whenever you’re watching a source

that is connected directly to your TV (such as an Internet connection), you can listen to

the sound through the AVR.

Power Control: This setting links the power on/off functions of the AVR to those of a TV

connected to its HDMI Monitor Out connector. When Power Control is set to On, turning

the TV’s power off will automatically put the AVR into the Standby mode; turning the TV’s

power on will automatically turn the AVR on. NOTE: The connected TV must support the

HDMI System Standby CEC (Consumer Electronics Control).

TV Control: This setting extends some audio-control functions between the AVR and a TV

connected to its HDMI Monitor Out connector. When TV Control is set to On, if the TV is set

to use external speakers, the TV’s internal speakers will mute, and you can use the TV’s

remote to control the AVR’s volume up/down and mute functions. If the TV is set to use

its internal speakers, the AVR’s output will automatically mute. NOTE: The connected TV

must support the HDMI Remote Control/System Audio Control CEC (Consumer Electronics

Control).

0295CSK - HK (x65Series) AVR3650_365_2650_265 CORE OM, WORK18 danny.indd 39 01/07/11 11:34:09

Harman Kardon AVR 265 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 265

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info