Bedienungsanleitung Harman Kardon AVR 347 (Seite 28 von 76) (Englisch)

502541

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

INSTALLATION

remote control to operate the iPod, and even charge the iPod while

it’s docked in The Bridge.

Simply plug the proprietary cable from The Bridge into the special

The Bridge/DMP connector on the rear of the AVR 347. See Figure 29.

Refer to the owner’s manual for The Bridge to select the appropriate

insert to match your iPod.

Figure 29 – The Bridge/DMP Connector

Step Five – Connect Video Display

Only video connections should be made between the receiver and

your video display (TV), unless your TV is the source for your television

programming (see Video 3 Source on page 26).

If you used an HDMI video connection for any of your sources, then con-

nect the HDMI Output on the AVR to an HDMI input on your video display.

See Figure 30. Consult the owner’s guide for your television to learn

the proper procedure for disabling or muting the audio. Unless you have a

non-HDMI source device that outputs 1080i or higher video via an analog

component video connection (see note below), no other video connections

are required, thanks to the AVR 347’s ability to transcode analog video

signals to HDMI, and you may proceed to Step Six.

IMPORTANT NOTE: The AVR 347 cannot convert 1080i or

1080p analog video signals to the HDMI format and outputs 1080i

signals, as is, to the Component Video Outputs. This affects users

of Microsoft Xbox 360 systems and some older set-top boxes.

If your digital cable television set-top box outputs 1080i or higher

video via component video outputs only contact your cable operator

for a replacement unit equipped with an HDM output.

For Xbox 360 or satellite receivers with no HDMI output, connect

the AVR’s Component Video Monitor Outputs to the TV, or change

the settings on your source device so that it outputs only 720p

video through its component video outputs, which the AVR can

convert to the HDMI format. Although you could connect the source

device’s component video outputs directly to your video display, you

would then have to select the correct video input on the display to

match the AVR’s input.

Figure 30 – HDMI Output

If your television does not have HDMI or DVI video inputs, you will need

to make a video connection for each type of video used for your sources.

First, determine what types of video your display is capable of handling.

Component video is preferred, followed by S-video and then composite

video. Ideally, this guided you in selecting the video connections for your

sources.

Next, note which types of video connections you used for your source

devices. Make sure you didn’t use a better type of video connection

for a source than your video display can handle. If so, disconnect the

source and use a video connection that’s compatible with your display.

If you used component video for any sources, connect the Component

Video Monitor Outputs on the receiver to one set of component video

inputs on your display. See Figure 31. The AVR 347 is able to transcode

composite and S-video sources to component video. If your video dis-

play has component video inputs, then you need only to connect the

Component Video Monitor Outputs and you may proceed to Step Six.

Figure 31 – Component Video Monitor Outputs

If you used S-video for any sources, connect the S-video Monitor output

on the receiver to an S-video input on your display. See Figure 32. The

AVR 347 converts composite video sources to S-video. If your video

display has S-video inputs, then you need only to connect the S-Video

Monitor Output and you may proceed to Step Six.

If you used composite video for any sources, but not component video

or S-video, connect the Composite Video Monitor output on the receiver

to a composite video input on the display. See Figure 32.

Figure 32 – S-Video and Composite Video Monitor Outputs

Consult the manual for your TV to make sure you understand how to

select each video input.

Step Six – Plug in AC Power

Having made all of your wiring connections, it is now time to plug each

component’s AC power cord into a working outlet.

You may plug one device into the AC Switched Accessory Outlet on the

rear of the AVR 347. See Figure 33. Make sure this device draws no

more than 50 watts. The device should have its mechanical or master

power switch turned on, and it will power on any time the AVR 347 is

turned on.

Figure 33 – Switched AC Accessory Outlet

Before plugging the AVR 347’s AC Power Cord into an electrical outlet,

make sure that the Master Power Switch on the front panel is popped

out so that the word OFF appears on its top. Gently press the button to

turn the switch off. This will prevent the possibility of damaging the AVR

in case of a transient power surge.

The AVR 347 is equipped with a detachable power cord. It allows

you to fully wire your system before installing the AVR, which may be

required for some in-wall entertainment centers or custom applications.

The male end of the cord should be plugged into an unswitched AC

power outlet, and the female end should be plugged into the receptacle

on the AVR 347’s rear panel. See Figure 34.

AVR347 om.qxd 7/10/07 11:01 AM Page 28

Harman Kardon AVR 347 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 347

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info