Bedienungsanleitung Harman Kardon AVR 347 (Seite 30 von 76) (Englisch)

502541

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Figure 36 – Input Selectors

4. Enter a code from Step 1, above.

a) If the device turns off, then press the Input Selector again to accept

the code; it will flash. The remote will exit the Program mode.

b) If the device does not turn off, try entering another code. If you

run out of codes, you may search through all of the codes in the

remote’s library for that product type by pressing the

⁄

Button repeatedly until the device turns off. When the device turns

off, enter the code by pressing the Input Selector, which will flash.

The remote then exits Program mode.

5. Once you have programmed a code, it’s a good idea to try using

some other functions to control the device. Sometimes, manufacturers

use the same Power code for several different models, while other

codes will vary. You may wish to repeat this process until you’ve

programmed a satisfactory code set that operates most of the

functions you frequently use.

6. You may find out which code number you have programmed by

pressing and holding the Input Selector to enter the Program mode.

Then press the Set Button, and the LED will flash in the code

sequence. One flash represents “1”, two flashes for “2”, and so forth.

A series of many fast flashes represents “0”. Record the codes

programmed for each device in Table 3.

Table 3 – Remote Control Codes

After you have programmed a code set to operate a device, test the

functions to see which ones may be missing or not operating correctly.

You may “learn” individual key codes if you have the device’s original

remote control by following this procedure:

a) Place the two remotes so that their IR transmitters face each other

end to end, separated by about one inch. See Figure 37. The

AVR 347 remote’s transmitter also serves as an IR receiver during

the learning process.

Figure 37 – AVR 347 and Original Remote Head-to-Head

b) Press the Input Selector for the device mode you wish to learn a

code into, and place the AVR 347 remote in Learning mode by

pressing and holding the Learn Button until the Program Indicator

flashes in amber, then release. See Figure 38.

Figure 38 – Learning Remote Commands

c) Press the button on the AVR 347 remote you wish to program with

the new code, and the Program Indicator will light steadily in amber.

d) Press and hold the button on the device’s original remote whose

code you wish to “learn” until the Program Indicator flashes in

green, then release it.

e) You may program additional buttons by repeating steps c) and d).

Press the Learn button once to exit Learning mode. If you prefer, you

may wait for the remote to “time out” and exit Learning mode on its

own, but this will take about 30 seconds.

If you are unable to locate a code set that correctly operates your

source device, it will not be possible to use the AVR remote to control

that device. However, you may still connect the source to the AVR 347

and operate it using the device’s original remote control. Alternatively,

you may wish to consider purchasing Harman Kardon’s optional TC 30

activity-based remote, which is programmed by accessing a large data-

base of product codes on the Internet. The TC 30 is also capable of

“learning” codes from your device’s original remote.

Most of the button labels on the remote describe the button’s function

when used to control the AVR 347. However, the button may perform

a very different function when used to control another device. Refer to

the Remote Control Function List, Table A8 in the Appendix, for a list of

each button’s functions with the various product types.

If you wish, you may program Macros, which are preprogrammed code

sequences that execute many code commands with a single button

press. You may also program “punch-through” codes, which allow the

remote to operate the volume, channel or transport controls of another

device without having to switch the remote’s device mode. See pages

60–61 for instructions on these advanced programming functions.

Source Input Product Type Remote

(circle one) Control Code

Video 1 VCR, PVR

Video 2 Cable, Satellite

Video 3 TV

Video 4 TV

HDMI 1 DVD, PVR, CBL, SAT

HDMI 2 DVD, PVR, CBL, SAT

DVD DVD

CD CD, CDR

INSTALLATION

AVR347 om.qxd 7/10/07 11:01 AM Page 30

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR 347 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 347

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info