Bedienungsanleitung Harman Kardon AVR 347 (Seite 37 von 76) (Englisch)

502541

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

INITIAL SETUP

The first line indicates that the receiver is currently set to the DVD source.

Press the Set Button, and then use the

›

to view the next source.

The sources will be selected

in the following order: Video 1, Video 2,

Video 3, Video 4, HDMI 1, HDMI 2, 6CH Direct, 8CH Direct, DMP/

The Bridge, Tape, CD, TUNER and XM. Pressing the

‹

Button selects

the sources in the reverse order.

For each of these sources, you may adjust the following settings. At a

minimum, you should make sure that sources connected to any of the

component video or digital audio inputs have the correct settings. Other

settings are optional, and you may adjust them at a later time when you

have more experience with the AVR. Refer to the Table A4 worksheet in

the appendix that you filled out during installation as you assign inputs

to each source.

TITLE: You may change the display name for any source. Not only

does this enable you to customize your system; it helps you to select

the correct source device even when you have forgotten which physical

connections were used.

Move the cursor down to the TITLE line and press the Set Button.

The screen shown in Figure 62 will appear.

Figure 62 – Retitling a Source Input

Use the Navigation Buttons to highlight the desired letter (or other

character), and press the Set Button to add it to the new title, which

will be displayed in the bar at the top of the screen. You may use the

Navigation Buttons, or select the left or right arrow and press the Set

Button, to move the cursor within the new title. To add a space either

move the cursor one character to the right as described above, or

highlight the SPACE indicator on screen and press the Set Button.

You may edit a title by inserting or deleting characters. To insert a new

character between two existing characters, move the cursor to highlight

the character to the right of the insertion point in the bar at the top of

the screen. Then highlight the INS indicator on screen and press the

Set Button. You may now select a character to insert in the new space.

Delete a character by moving the cursor to highlight the unwanted

character in the bar at the top of the screen. Then highlight the DEL

indicator on screen and press the Set Button.

When you have finished entering the new title, highlight the OK indicator

and press the Set Button to return to the Input Setup menu. Although

the Source Input name will remain the same in the Input Setup menu,

the new title will appear in the semi-OSD displays and the front-panel

display as appropriate.

NOTES:

• Only upper case letters are available for titles.

• Normally both the source input and the digital (or analog)

audio input selection appear on the upper line of the semi-

OSD and front-panel displays. When The Bridge source is

selected, its status as CONNECTED or UNPLUGGED appears

in place of the audio input selection. However, when a source

input is retitled, the audio input selection (or status of The

Bridge) no longer appears unless you press the Digital Input

Selector on the remote or front panel.

VIDEO IN: This setting reflects the video input that is assigned to the

source. The default assignment for all sources is COMPOSITE except

as shown in Table 5:

Table 5 – Default Video Inputs

We recommend that you leave the setting for the HDMI sources as is.

For the other sources, change this setting to reflect use of the Component

1, 2 or 3 Video Input as appropriate. If you used the composite or

S-video input for any source, make sure this setting is COMPOSITE.

(There is no separate selection for S-video.)

NOTE: If your video display has an HDMI input, then you only

need to connect the AVR’s HDMI Output to the display. The

AVR 347 transcodes analog source video signals up to 720p from

composite, S-video or component video to the HDMI format, and

is also capable of upscaling the signal up to 720p to match your

display’s capabilities. The only exception to this rule is for analog

1080i/p sources, which are not available at the HDMI Output, but

1080i signals are passed, as is, to the Component Video Outputs.

If your source device is a Microsoft Xbox 360 or an older set-top

box that outputs 1080i or higher video via component video

outputs, then set the source to output 720p video, or connect the

AVR’s Component Video Monitor Outputs to your video display.

If your display does not have an HDMI input, but does have compo-

nent video inputs, you only need to connect the AVR’s Component

Video Monitor Outputs to the display. The AVR 347 transcodes com-

posite and S-video signals to the component video format. Similarly,

if your display’s best-quality video input is S-video, you do not need

to connect the Composite Video Monitor Output to the display; any

composite video source signals will be converted to S-video format,

and S-video signals may be converted to composite video format if

your video display is not equipped with an S-video input.

Source Input Default Video Input

DVD Component 1

Video 1 Component 2

Video 2 Component 3

HDMI 1 HDMI 1

HDMI 2 HDMI 2

AVR347 om.qxd 7/10/07 11:01 AM Page 37

Harman Kardon AVR 347 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 347

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info