Bedienungsanleitung Harman Kardon AVR 347 (Seite 38 von 76) (Englisch)

502541

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

INITIAL SETUP

AUDIO IN: By default, the analog audio inputs are assigned at

the factory to all sources, with the following exceptions:

Table 6 – Default Digital Audio Assignments

If you used a digital audio connection for another source, change this

setting to assign the correct digital audio input to the source, even if you

also connected the analog audio outputs of the source to the receiver.

AUTO POLL: The Auto Poll feature is used when both an analog audio

and digital audio connection have been made for one source device.

If for some reason no digital signal is available, the AVR 347 will switch

to the analog inputs for the source. This situation can occur with some

cable or satellite television broadcasts, where some channels are broad-

cast with digital audio and others with analog audio.

For some sources, the Auto Poll feature is unnecessary and may be

undesirable. For example, if your DVD player is stopped, you may not

want to use the analog audio signal or you may have decided not to

connect analog audio. Move the cursor to this line, press the Set Button,

and press the

‹/› Buttons until OFF appears, disabling the Auto Poll

feature. With Auto Poll turned off, the receiver will only check for a signal

at the audio input assigned to the source.

NOTE: Since The Bridge is connected to the AVR using a

dedicated audio connection, it isn’t possible to select a different

audio input for this source. The AM/FM/XM tuner and 6-/8-

Channel Inputs also use dedicated audio inputs, and it isn’t

possible to select a digital audio input for these sources.

The next three lines in the Input Setup menu activate the tone controls,

and may be skipped at this time. We recommend leaving the tone

controls at their factory defaults for most listening, in order to enjoy the

sound mix created by your favorite movie and music artists. However,

if your room or speakers have unusual characteristics, or simply as

a matter of personal preference, see the Tone Controls section on

page 40 for more information.

VIDEO MODE: This setting is used only with a fully analog video path

(composite, S-video or component video). It has no effect on HDMI

sources and video displays. Due to the design of some analog video

displays and the nature of the video standard, there may be timing

issues with the AVR. If you observe some minor video instability when

using the AVR’s analog video outputs, try changing the Video Mode

setting to Mode B. If you continue to observe problems, connect your

source device’s video output directly to the video display, or consider

upgrading to an HDMI-capable display.

You are now ready to begin enjoying your new receiver!

Source Input Default Digital Audio Input

DVD Coax 1

Video 2 Optical 1

HDMI 1 HDMI 1

HDMI 2 HDMI 2

AVR347 om.qxd 7/10/07 11:01 AM Page 38

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR 347 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 347

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info