Bedienungsanleitung Harman Kardon AVR 4000 (Seite 40 von 58) (Englisch)

8518

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

40 PROGRAMMING THE REMOTE

Programming the Remote

1. Press and hold both the Input Selector

for the device you wish to find the code for and

the Mute button

at the same time. Note

that the Program/SPL Indicator

will ini-

tally turn amber and begin flashing. Release the

buttons and begin the next step within 20 sec-

onds.

2. Press the Set button

.The Program/SPL

Indicator

will then blink green in a sequence

that corresponds to the three-digit code, with a

one-second pause between each digit. Count the

number of blinks between each pause to deter-

mine the digit of the code. One blink is the number

1, two blinks is the number 2, and so forth. Note

that a rapid sequence of three blinks is used to

indicate a “0.”

Example: One blink, followed by a one-second

pause, followed by six blinks, followed by a one-

second pause, followed by four blinks indicates

that the code has been set to 164.

For future reference enter the Setup Codes for the

equipment in your system here:

DVD ____________ CD ________________

VID1/VCR ________ VID2/TV __________

VID3/CBL/SAT ______________________

TAPE ______________________________

Learning Codes from a Remote

In addition to using codes from the remote’s

internal code library, the AVR 4000’s remote is

able to “learn” codes from remotes that may not

be in the code library. In addition, you may use

this function to “learn over” the codes from a

preprogrammed device to add functions not

included in the preprogrammed codes. To learn

or transfer codes from an IR remote to the AVR

4000’s remote, follow these steps:

1. Place the front of the original remote with the

code being sent so that it is facing the IR

Transmitter Window

on the AVR 4000

remote “head-to-head.” The remotes should be

between 2 and 4cm apart.

2. Select the button on the remote that you wish

to use as the device selector for the codes about

to be entered. This must be any of the Input

Selectors

(except for VID4).

3. Press the Input Selector

button chosen

and the Learn Button

at the same time.

Hold these buttons until the Program/SPL

Indicat

flashes amber and the light under

the device selector button turns red. Release the

buttons. It is important that you begin the next

step within 20 seconds.

4. Press the button on the AVR 4000 remote that

you wish to program. Note that the Program/

SPL Indicat

will stop flashing.

Important Note: Codes cannot be taught to all

buttons on the remote. The buttons with the

following numbers are not learnable (for

numbers, see drawing on page 11): 6, 7, 8, 36,

37, 9, 12, 33, 19, 29, 20, 21, 22, 23, 26, 27, 28.

5. As long as the Program/SPL Indicator

is on, press and hold the button on the original

remote that you wish to “teach” into the

AVR 4000 remote.When the Program/SPL

Indicator

turns green, release the button.

Note that the Program Indicator will then begin

to flash amber again.

NOTE: If the Program/SPL Indicator

turns

red during Step 5, the programming was not suc-

cessful. Repeat the steps to see if the code will

“take.” If the indicator keeps flashing red in

step 5, this code cannot be taught.

6. Repeat steps 4 though 5 for each button on

the source remote that you wish to transfer to

the AVR 4000 remote.

7. Once all codes have been transferred from the

original source remote to the AVR 4000 remote,

press the Learn button

. This will turn off all

LEDs and turn off the learning mode.

8. Repeat Steps 1 through 7 for any additional

remotes you wish to “teach” into the AVR 4000

Remote.

Erasing Learned Codes

The AVR 4000’s remote allows you to remove or

erase the code learned into a single button for a

single device, to remove or erase all the codes that

have been learned for a single device, or to erase

all commands that have been learned for all

devices.

To erase a single learned code from within a single

device’s settings, follow these steps:

1. Press and hold both the Input Selector

456

within which the individual button to

be erased has been programmed and the Learn

button

2.When the red LED under the Input Selector

turns red and the Program/SPL Indicator

flashes amber, release the buttons.

3. Press and release the Input Selector

456

again for the device within which the

individual button to be erased has been pro-

grammed.

4. Press the 7 button

three times.

5. Press and release the individual button for

which the code is to be erased.The Program/SPL

Indicator

will blink green two times and

then return to amber.

6.To erase other buttons within the same device,

press them as noted in Step 5.

7.When all buttons to be erased have been

pressed, press the Learn button

to complete

the process.

To erase all codes within a single device, follow

these steps:

1. Press and hold both the Input Selector

456

for which you wish to erase the

codes and the Learn button

2.When the red LED under the Input Selector

turns red and the Program/SPL Indicator

flashes amber, release the buttons.

3. Press and release the same Input Selector

456

again for the device whose codes

you wish to erase.

4. Press the 8 button

three times.

5.The Program/SPL Indicator

will turn off

and the red light under the Input Selector will

flash on and off once to indicate that the codes

have been erased.

Harman Kardon AVR 4000 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 4000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info